AdBlock Warning

Parts of this website do not function properly with AdBlock enabled on your device. To get the best user experience on our website, please disable Adblock for this website (domain) on your browser.


Budding Enthusiast
  • Content count

  • Joined

  • Last visited

About apness

  • Rank

Profile Information

  • Ford Model
    fusion 1 tdci 54 plate
  1. You could try taking the dash off an seeing if the cable/control behind the heating dial on the dash has broken or become disconnected? If all else (head gasket, heater itself) is ok might be something as simple as a snapped cable to the heater control.
  2. Realise this isn't a busy thread, but figured I'd ask - is it worth chipping the 1.4 diesel and does it make much difference to its sluggish performance? I've had my leon (tdi 150) chipped since 2k miles and its hard to drive the car without it - feels like a snail unchipped - so figured it'd be worth doing the same to the wifes car to make it a bit less 'challenging' at junctions and when the road opens up a bit. Might be better on fuel too hopefully with not having to thrash it so hard. The Leon does about 4-500 on a tank depending on driving but chipped tends to do a few more mpg thanks to more torque less hard work, hopefully the little ford might do the same.
  3. I realise I'm a new poster so my request might seem a bit dodgy, but have been trying to sort this out for a little while now Wife got a fusion 1 tdci from her dad in part ex for her old ratty bora tdi - which was faster, better on fuel, comfier etc but had loads of dents and bangs in it and various warning lights on the dash, so she did a swap and he traded that in on his c-max. Only thing is, being a fusion 1 its proper poverty spec - wind your own windows and a casette (!) player. I bought another (Ford) cd player off ebay - don't know if it even works yet as I'm having a swine of a time getting the centre panel off! I got the various screws off required at top, bottom, middle, pulled the panel away unhooked the hazard switch and heater cable, also air direction (blue twirly thing!) selector but there's something I can't see stopping me pulling the panel away far enough to get the old radio out. I can get to the screws but the panel just won't pull away far enough to remove it. Bought a haynes manual (the burgundy one, for fiestas) as it's the nearest to it but that hasn't shed any light as there are different screws (and lower half of steering column plastics) to take off apparently on fiesta - can't see having to do that for the fusion. So does anyone have a workshop manual or a parts fiche diagram of the heater console wiring on a fusion? There's one cable or wire - something that feels 'sprung' stopping me pulling the console away. Put it all back now but left the screws out so I can get to it in 5 minutes, but this is annoying me now! Watch, I'll get the new cd player in and it'll be a duffer after all this hassle! Didn't even get a code for it <_< but figured that one out via the internet... Also, in my Seat Leon I have a 20gig hard drive hooked up to the cd via the changer socket. Is there anything like that for fords? (Mine's called a 'phatbox' I bought in a group buy off Anything basically to bring the car into the 21st century as the spec of the thing wouldn't be out of place on an early 80s motor... Can't complain - it was effectively, 'free' (sort of - her bora wasn't worth much and this has 18k miles on it) but it's a bit of a step down for her until we can afford something else. Or she has mine and I get something else :) Cheers, Paul
  4. Hello all, just joined up as the wife now owns a ford fusion - figure this is the best place for info about the car and pass on info as I find it out. I drive a leon tdi 150 suitably chipped up but wanting something faster now, funds permitting. Anyhow, hi all :) Cheers Paul