Ford Owners Club - Ford Forums Messages

FORD FAIR – SILVERSTONE – 6TH AUGUST 2017

Join us on the Ford Owners Club stand at Ford Fair, Silverstone on Sunday 6th August 2017.

Click this link to find out more



Stoney871

Super Mod
  • Content count

    22,295
  • Joined

  • Last visited

  • Days Won

    209

Stoney871 last won the day on April 10

Stoney871 had the most liked content!

7 Followers

About Stoney871

  • Rank
    Resident Lawkeeper
  • Birthday 04/24/1970

Contact Methods

  • First Name
    Clive

Profile Information

  • Gender*
    Male
  • Ford Model
    2015 Focus ST3 300bhp
  • Ford Year
    2015
  • UK/Ireland Location
    Devon
  • Annual Mileage
    20,001 to 25,000
  • Interests
    Car Modification
  • Contributor
    5

Previous Fields

  • Location
    Devon

Recent Profile Visitors

32,219 profile views
  1. W16 ? Sent from my SM-G930F using Tapatalk
  2. It's spot on, the finish is like glass. Sent from my SM-G930F using Tapatalk
  3. I matched up the nozzles to the body colour. Nice deep impact blue. Pity the rubber seals have to stay original though. Sent from my SM-G930F using Tapatalk
  4. Strangely enough I fitted a pair of colour matched nozzles last night. Paintmodz is indeed on ebay now. The nozzles are all original. Took maybe 10 minutes to swap. Curiously the spray pattern seems better than the original nozzles. Sent from my SM-G930F using Tapatalk
  5. Most parts are interchangeable (some may need minor modifications). A 2009 would be classed as a mk2.5. Sent from my SM-G930F using Tapatalk
  6. The main box still has a viewing card but the extra boxes don't. Sent from my SM-G930F using Tapatalk
  7. The reason that the mk scheme seems muddled is because Ford do not officially subscribe to one. They purely go bu the uear of the model. When buying parts, go by year to avoid problems. Sent from my SM-G930F using Tapatalk
  8. Duratec refers to the engine type whereas Zetec is the build level. Concerning the engine performance, it could be a worn clutch plate. Sent from my SM-G930F using Tapatalk
  9. The vaccine only contains the previous years strain so only gives a small protection as the strain mutates every year. That's why it can't be cured once and for all. Sent from my SM-G930F using Tapatalk
  10. Check the wiper is getting power. If it's not then inspect the wiring in the rubber sleeve between the roof and bootlid, it's a known point for broken wires. Sent from my SM-G930F using Tapatalk
  11. Look at the VIN plate in the door shut on your car. Second box up on the left is your paint code, it will give the paint mixer the colour and year it was introduced. Colours do vary slightly depending on the year.
  12. I haven't done the job myself (thankfully) but i think I may be able to start you off. The speaker cover needs to come off so you can access the bolt(s) underneath. Pull the front side out without bending it too much and then you will see a trim clip at the back, you need a trim removal tool (bojo tools are preferred but may not be rigid enough to get the clip out properly) be cautious as they can snap. Get the tool in between the part outside the slot in the speaker trim and the door body and wiggle it out, there may be another (not 100% sure but be prepared to lever the second one out if it exists) and then the speaker trim should be removeable. Disconnect the speaker wires then the mirror wiring. The mirror bolt(s) is/are behind a grommet that pops out. Mirror should then come off, there is a lip at the top of the mirror mount trim so pull outwards from the bottom first. Some photos from my car that may assist you- Trim clip in detail- Metal trim tools- Plastic Bojo tools- Short of stripping my car back myself i can't advise further but hopefully this puts you on the right track.
  13. Have you thought of one of these?- http://www.ebay.co.uk/itm/122029160115?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
  14. Tilt the glass down as far as it will go and pull it towards you and the tabs will disengage. Just unclip the heater wires and then reverse to fit the new lens. Sent from my SM-G930F using Tapatalk
  15. Sky Q is indeed run on wifi. The main box has 2 inputs and acts as the main media server. You get a new dual channel router with the installation. All the extra boxes only need a power supply and a good wifi signal, no other input wires needed (although you can use a wired network if preferred). Sent from my SM-G930F using Tapatalk