• Announcements

    • Stoney871

      Posting in General Chat thread.   11/11/2017

      it has been noted that too many Members are posting messages in the General Chat area instead of the correct Forums. Any messages posted in the General Chat area that are not General Chat will be deleted without warning and offenders may recieve warning points if repeated instances are seen from that Member. There are plenty of different Club areas that encompass 99% of Ford related posts, please select and use the correct one. If anyone is not sure of which area to post something then feel free to P/M myself or other Senior Staff for guidance. The Moderating Staff are having to spend far too much time chasing this problem instead of maintaining the other areas of the forum.


Petrif74

Budding Enthusiast
  • Content count

    2
  • Joined

  • Last visited

About Petrif74

  • Rank
    Newbie

Contact Methods

  • MSN
    petrifohr@msn.com
  • First Name
    Petri

Profile Information

  • Gender*
    Male
  • Ford Model
    ST225
  • Ford Year
    2006
  • UK/Ireland Location
    Other/NonUK

Previous Fields

  • Location
    Finland
  1. Hello Is anyone knows is this cruise control possible to focus st 2.5? I have st 2006 year.
  2. Hello Is it possible program Focus ST 2.5 with cruise control? I installed cruise control buttons and GEM-test they beep. But why doesnt working? I do all this but this Step 3d PCM – Procedures – Page 2 Click “Load VID-block from file” my Elmconfig doesnt show that VID-block selections? why? Now the programing begins! Step 1 – Switch in MS-CAN position (left) GEM – Configuration – Page 3 Click “Read from GEM” If “Cruise Control Configuration” it ticked then move to the next step, if not then tick it Click “Write to GEM” Wait for program to write and reboot the GEM Step 2 – Switch in HS-CAN position (right) HEC – Configuration – Page 1 If “Cruise Control Configuration” it ticked then move to the next step, if not then tick it Click “Write to HEC” Wait for program to write and reboot the HEC Step 3a – Switch in HS-CAN position (right) PCM – Configuration Click “Read from PCM” Make sure “Integrated Speed Control” is ticked Click “Save to file” – save it to a clutter free, easily accessible folder (I recommend desktop) Step 3b – Switch in HS-CAN position (right) PCM – Procedures – Page 2 DO NOT CHANGE ANY SETTINGS! Click “Read firmware from PCM to BIN-file” – this takes anything *this bit I struggle to remember but don’t worry it wont ruin your car! Once you click read you might get an option to save the bin file (this might be before or after the reading). If after reading it does not prompt you to save anything then click “Save firmware to BIN-file”, chose the same location where you saved the PCM configuration file. Now close ELMconfig 2.17 and open 2.10 Make sure the settings are the same as used in 2.17 (note the device won’t show its name instead it will just display its com port but this is auto detected) and click open port. Step 3c - Switch in HS-CAN position (right) PCM – Information Click “Read” and wait for it to read all the fields. Step 3d - Switch in HS-CAN position (right) PCM – Procedures – Page 2 Click “Load VID-block from file” Here you want to select the PCM configuration file you saved (the one where you ticked integrated speed control) Click “Load firmware from file” Now select the file you saved from reading the PCM to bin operation (the one that took a long time in comparison) Click “Write current firmware in PCM” This will reprogram the PCM, it will take anything from 1 – 10 minutes. You may get an engine malfunction warning appear while reprogramming, do not worry this is normal and happened to me, it because the PCM module is not able to communicate while its being reprogrammed so it shows as an error. DO NOT UNPLUG or STOP to process or you will mess up your PCM. Once its done it will reboot and inform you its complete, now simply close elmconfig and remove the cable, start your engine and take your foci out for a drive and try cruise – IT will work !!!