Search the Community

Showing results for tags 'plug removing + tool making'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Welcome to Ford Owners Club
    • Review your Ford
    • Discount Scheme
    • New Member Introductions
    • Was it you!? FOC Members Spotted!
    • General Ford Related Discussions
    • General Chat
    • Ford Guides
    • Show off your motor!
    • Car Insurance Discussions
  • Ford Models
    • Ford Fiesta Club
    • Ford Focus Club
    • Ford Mondeo / Vignale Club
    • Ford Mustang Club
    • Ford KA / StreetKA Club
    • Ford Kuga Club
    • Ford Edge Club
    • Ford B-Max Club
    • Ford C-Max Club
    • Ford S-Max Club
    • Ford Galaxy Club
    • Ford EcoSport Club
    • Ford Fusion Club
    • Ford Puma Club
    • Ford Escort Club
    • Ford Sierra Club
    • Classic Ford
    • Ford Transit Club
    • Ford Ranger Club
  • Buy & Sell
    • Club Cars For Sale
    • Ford Parts For Sale
    • Classifieds
    • General Items (Non Ford Related)
    • Wanted
    • eBay Finds
    • Buy & Sell Archive
  • Traders
    • Opie Oils
    • Mountune
    • Burton Power
    • Puma Speed
    • Revo
    • Visit Owners Club Insurance Page
    • Owners Club Finance
    • Advertise Here
    • Evans Halshaw ST-3 TDCI Deal
  • Ford Modifications and Projects
    • mountune Discussions
    • Photoshopped Ford Photos
    • Ford Project and Build Threads
    • Ford Modification Discussions
  • General Forums
    • Ford Owners Club Meets & Regional Discussion
    • Maintenance / Servicing / MOT Discussions
    • Dealer Problems & Consumer Advice
    • Technical Knowledge
    • Wheels & Tyres
    • Detailing your Ford
    • Audio & Electronics
    • General Site Requests
    • Computing, Gaming and Geeky
    • Dash Cam Videos
    • Ford Motorsport
  • Back Office
  • Ford How-To Guides

Categories

  • Ford Reviews
  • General Ford Guides - Modern Fords
  • Ford Fiesta Guides
  • Ford Buyers Guides
  • Ford Focus Guides
  • Ford Fusion Guides
  • Ford C-Max Guides
  • Ford S-Max Guides
  • Ford Ka Guides
  • Ford Mondeo Guides
  • Ford Kuga Guides
  • Ford Galaxy Guides
  • Ford Puma Guides
  • Ford Escort Guides

Calendars

  • Community Calendar

Categories

  • Articles

Found 1 result

  1. 1) Drive car up ramps ( I made ramps using 4 X 13 foot secondhand scaffold boards £5 each ). Disconnect battery negative connector. Jack up right hand side front of car off the ramp and support with axle stand. Remove front wheel and splash shield, 3 screws. ( Photo 1 ). 2) Remove nut from top of drop link using allen key and spanner. ( Photo 2 ). 3) Lever drop link downwards to easily push out the bolt attached to drop link. ( Photo 3 ). 4) Move drop link to one side so that there is a space to get alternator out. ( Photo 4 ). 5) Remove cooling cover on back of alternator 4 nuts ( 8mm spanner ) and remove 2 wiring connectors. The square connector looks difficult to remove but just press tab with sharpened bent strip of metal and pull plug off ( do not pull on wires ) ( Photos 5 & 6 ). 6) Make tool to release spring tensioner pressure from belt. Mine needed 12mm square X 20mm long bar of metal welded to 22 inch long 6mm strip of metal. Other Mondeos could need a hexagon shaped tool, not square. This tool fits square hole or hexagon shaped hole behind tensioner pulley. Pull to the left to remove pressure on the belt and lift the slack belt off alternator pulley( Photos 7, 8 and 9 ). If you don't have a welder a 12mm square X 20mm bar of metal and an adjustable spanner or mole grips with tube extension could do it but will probably slip off under pressure. 7) Remove top bolt from alternator ( this bolt also supports wiring harness ). Then from under car remove the other 2 nuts. This leaves 2 long studs that must be removed using E8 TORX socket or pliers but protect the threads. These studs are not very tight. There is now a clear space to lower the alternator. With these 2 studs removed it is also very easy to position the new belt.You will see this when refitting the belt. I purchased a set of TORX sockets from Amazon ( Silverline 675072 14 piece only £8.80 ) very useful for other jobs on the car. 8) Turn alternator so that widest part is horizontal and wiggle it through hole under wheel arch ( photo 10 ). I then also removed complete spring tensioner, another 3 bolts, to inspect it. ( nothing wrong with mine ). This has to be removed if you also want to change the belt. When refitting the spring tensioner and belt ONLY FIT ONE of the TOP 2 bolts loosely ( the outside bolt ) of the spring tensioner then its easy to get the new belt round the spring tensioner pulley as you can move the tensioner outwards to give a 10mm clearance between the engine block and pulley and just loop the belt round the lower bracket of the spring tensioner to get in correct position. Note: this is the reason the 2 studs must be out because if they were screwed in you would not get any 10mm movement to get the belt round the pulley and lower bracket. Now you can go ahead and screw the studs back in while holding the alternator in place plus the lower bracket of the spring tensioner. I forgot to position the lower bracket of the spring tensioner onto the 2 studs. Note how long the threads are on the studs without the spring tensioner bracket on. Make sure you fit the studs complete with alternator and spring tensioner bracket. Also make sure the lower bracket is not upside down, photo 12 is correct way round. ( photos 11 & 12 ). I found it easier to fit the belt on the alternator pulley last when using the spring tensioner release tool.To save your fingers get a piece of wood 60mm X 15mm X 2 foot long, round off one end to the shape of the alternator pulley ( thats 60mm diameter ). Hold the spring to max release pressure using the release tool so you can easily tap the belt onto the alternator pulley from the top of the engine using a rubber hammer on the piece of wood. NOTE: Your release tool must go FULLY into the square or hexagon hole behind the spring pulley. I have noticed that a new spring tensioner had the pulley bolt 4mm too long which only allowed the release tool to go half way in so when applying heavy pressure the aluminium casting breaks around the square hole. So check all new brackets and cut the pulley bolt flush with bottom of hole if too long. My car is an automatic and the crankshaft pulley was in good condition although rusty. Just for the record if you get another car, I consider the 5 speed tiptronic automatic gearboxes on Ford cars to be brilliant, I have had my Mondeo 2.0 TDCI Est Auto 2004 since new and this gearbox has not given any problems at all. No clutch or flywheel repairs on my car. Its done 142,000 miles on original battery, alternator and serpentine belt. I am only changing the belt today because it should be done at 50,000 miles but there was still no sign of wear. Hope these photos and explaination make it easy for you to do this job. Any problems just ask. Good Luck Dave