Jump to content


Photo

Fob Dont Bloody Work!


  • Please log in to reply
3 replies to this topic

#1 red but not so fast!

red but not so fast!

    Member

  • New Member
  • PipPip
  • 10 posts
  • Ford Model: 2008 mondeo mk 4 2.0 ghia tdci
  • Year: 2008
  • Location: Yorkshire

Posted 06 June 2010 - 07:34 PM

just had my windscreen replaced in my 55 plate tci mondeo zetec and my fob wont work in central locking! i can open it manually only to be greeted by the alarm every time i open the door! people think im nicking my own car and its startng to get to me! funny how that autowindscreens fit me a new window then my keys dont work! the mrs does though am i just being stupid anf its ironci that the battery might have failed at the same time!?
i had a look in my manual and it says try reprogramming!? turning it 4 times back and forth to position 2 within six seconds but this has done nothing! anyone got any advice? please?

Have something to contribute?

Sign in or register to start a topic...



Sign up to FOC Premium Membership To Remove These Ads

#2 chris bowman

chris bowman

    Feet Under The Table

  • New Member
  • PipPipPipPip
  • 255 posts
  • Ford Model: ford mondeo 2.0lx tdci 115

Posted 06 June 2010 - 09:25 PM

this is the only link i can find on the subject. u do have to turn the ign on and off quite quickly

http://fordwiki.co.u...ter_Programming

#3 bigbossowen

bigbossowen

    Settling In Well

  • New Member
  • PipPipPip
  • 49 posts
  • Ford Model: mk3 mondeo tdci 130

Posted 08 June 2010 - 07:07 PM

Remote Transmitter Programming (410040)

1. Note:
A maximum of four keyless entry remote transmitters can be programmed to the generic electronic module (GEM). Programming must be done at the same time for all the transmitters.

Note:
To enter programming mode, first make sure that the vehicle battery is fully charged and the anti-theft system is not armed or triggered (if equipped).

Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.

2. Turn the ignition switch from position I to position II at least four times in six seconds.

3. Turn the ignition switch to position I.

4. The GEM is now in the learning mode.

5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new transmitter code has been successfully received.

6. After each successful programming, another 10 second learning mode is automatically entered, up to a maximum of four times.

7. To program additional transmitters, repeat step 5.

8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.

9. Note:
An incorrect programming procedure does not affect the stored codes.

After successful programming, only the new programmed transmitters will be accepted.

10. Test all the programmed transmitters, by activating and deactivating the locking/unlocking functions.

#4 ponsaloti

ponsaloti

    Feet Under The Table

  • Budding Enthusiast
  • PipPipPipPip
  • 110 posts
  • Name: M
  • Ford Model: mondeo
  • Year: 2014
  • Location: Essex

Posted 08 June 2010 - 09:30 PM

First thing to do is take your remote to a good locksmith and get him to test it for a signal.
We dont charge for this service.


Not what you're looking for?

Register now, we have a huge community of enthusiasts to answer any questions you might have



0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users