1djspikey Posted January 20, 2012 Share Posted January 20, 2012 Hi all :) been for a Diagnostics test on my 2002 mondeo estate ghia 2.0 tdci euro 3 that goes into limp mode and glow plug flashing heres the codes ive been given :( U1900 CAN Communication Bus Fault P0100 Mass or Volume Air Flow Circuit Malfunction P0235 Turbocharger Boost Sensor A Circuit Malfunction P1665 Injection pump control module communications P1664 pump control module malfunction P1211 Injector Control Pressure Sensor Above / Below Desired engine running P0251 Injection Pump Fuel Metering Control A Malfunction i also had a vacuume pressure test on the EGR and was working well plus i did clean it all out a few weeks back so this problem was wiped off the list the turbo is vacuume actuator as been tested and is running fine and turbo is not that old by the looks of it pretty clean B) as anyone got any ideas and thoughts ?? regards spike ;) Quote Link to comment Share on other sites More sharing options...
Stoney871 Posted January 20, 2012 Share Posted January 20, 2012 You might find all those faults are caused by one sensor or connection playing up. I'm wondering if a CANBUS error is the root? I'm sure someone will be able to shed light on this. Quote Link to comment Share on other sites More sharing options...
TDCiST Posted January 20, 2012 Share Posted January 20, 2012 oooh CANBUS fault! not seen that before... Thats a lot of faults, surely if there is a CANBUS fault, it cant report other errors?? I'm confused!?!? Quote Link to comment Share on other sites More sharing options...
1djspikey Posted January 20, 2012 Author Share Posted January 20, 2012 the car runs sweet till you need to boot the turbo in 3rd and 4th gear heres the print out oh for got to mention ive put half a tank of diesel in and forte advanced formula diesel treatment in tank as made response better but still goes limp Quote Link to comment Share on other sites More sharing options...
TDCiST Posted January 20, 2012 Share Posted January 20, 2012 2002 diesel isnt it?? It could be that its not CANBUS compliant... My 2004 focus wasnt, would only do OBDII or whatever the other protocol was Quote Link to comment Share on other sites More sharing options...
1djspikey Posted January 20, 2012 Author Share Posted January 20, 2012 yeah it`s 2002 euro 3 got all the vacuume valves on and egr right handside at the back Quote Link to comment Share on other sites More sharing options...
stef123 Posted January 20, 2012 Share Posted January 20, 2012 Can you get those codes cleared and see what reappears? Quote Link to comment Share on other sites More sharing options...
1djspikey Posted January 21, 2012 Author Share Posted January 21, 2012 Can you get those codes cleared and see what reappears? Hi steff The codes was reset 2weeks ago so these are resent codes over the past 2weeks if you know what i mean spike Quote Link to comment Share on other sites More sharing options...
1djspikey Posted January 21, 2012 Author Share Posted January 21, 2012 can you just replace FORD MONDEO MK3 TDCi FUEL METERING VALVE SENSOR plus fuel pump tempeture sensor or do you have to recode them also can you just replace the top rail sensor or is the a recode spike Quote Link to comment Share on other sites More sharing options...
mintalkin Posted January 21, 2012 Share Posted January 21, 2012 diesels did not become eobd untill 2004 so unless they have the correct reader it could throw up all sort of codes hence the canbus error. Quote Link to comment Share on other sites More sharing options...
gmac187 Posted August 15, 2012 Share Posted August 15, 2012 Hey guys... Got a P2263 turbo/charger boost system performance fault. Flashing glow plug but no ECU light It's a 53 2.0 TDCi Ghia.. In limp mode at moment... Had egr off and cleaned. Been reading lots about this just wondered if anyone has had that same code before? If so, what is the best course of action? Thank you ... Quote Link to comment Share on other sites More sharing options...
stef123 Posted August 15, 2012 Share Posted August 15, 2012 Hey guys... Got a P2263 turbo/charger boost system performance fault. Flashing glow plug but no ECU light It's a 53 2.0 TDCi Ghia.. In limp mode at moment... Had egr off and cleaned. Been reading lots about this just wondered if anyone has had that same code before? If so, what is the best course of action? Thank you ... have you checked the hoses for splits? Quote Link to comment Share on other sites More sharing options...
piper Posted August 15, 2012 Share Posted August 15, 2012 Going for a diagnostic test tomorrow with pretty much the same problem , glow plug light comes on when i put my foot down (hard) and then the car goes into limp mode. It will re-set it self when i turn the engine off. It will be interest to see what come up, not much i hope. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Ford UK Shop
Sponsored Ad
Name: eBay
Ford Model: FordUK Shop
Ford Year: 2024
Latest Deals
Ford UK Shop for genuine Ford parts & accessoriesDisclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.