Jump to content
Do Not Sell My Personal Information


Guide Fitting Cruise Control Focus Mk2 & Mk2.5 And Ford C-Max


Pidu
 Share

Recommended Posts

Thats the wrong connector. Try the one in the passenger footwell lol

  • Like 1
Link to comment
Share on other sites


Thats the wrong connector. Try the one in the passenger footwell lol

:huh: :D

  • Like 1
Link to comment
Share on other sites

was that a homer "doh" moment i detected there?? lol

Link to comment
Share on other sites

:iim: . Now that I found it , I am most :( ... no wires in pin 10/18.

Link to comment
Share on other sites

should be a brown and white wire. you may have missed it...there are two blue connectors on the fusebox...Well mine did anyways lol

Its the one where you pull the fuse box down and as you look at it top left.

I can remember seeing somewhere that a ford tech has never seen a car without them

Link to comment
Share on other sites


John H,

I think this is the one right ? This time I hope I am wrong.

Btw, the brown and white wires, are they just the ones that directly run into the plug behind the steeering wheel ? If yes, I am wondering running the 2 cables separately would work.

20130604_004549.jpg

20130604_004609.jpg

However, I noted that there is the 2 switches on the brake pedal.

Since my car is an Auto Transmission (Powershift), I didn't check for the clutch switch.

20130604_010602.jpg

Link to comment
Share on other sites

looks as though you have a few wires missing there. Yeah thats the switches - you wont have clutch one if its an auto.

Check under the steering wheel on the connector there...Is there a brown and white wire?

Link to comment
Share on other sites

Just to keep everyone informed. I now have cruise control in my focus :D i spent £10 on the componants for the buttons

Link to comment
Share on other sites

I used IDS to activate and recalibrate the modules for cruise. Im willing to do this for anyone in tyne and wear and durham area

Link to comment
Share on other sites

  • 3 weeks later...

Hi, Using EML config 0.2.7b to configure the PCM for Cruise Control is it the box 'Integrated Speed Control' which has to be ticked?

Thanks

Link to comment
Share on other sites

  • 2 weeks later...

Finally got out and checked my wiring, I think the wiring is there, but if anyone can clarify...

IMAG0001_zps902c9b9d.jpg

IMAG0002_zpscde83bfd.jpg

IMAG0003_zpsf0ae421c.jpg

IMAG0004_zps36fb3e74.jpg

Wires going to the steering wheel column, I believe all the wires are here:

IMAG0005_zpsde187644.jpg

Link to comment
Share on other sites

yep they there, look at both solid brown and solid white wire.

Link to comment
Share on other sites


now just get your head under near the pedals and check for two switches on brake and one on clutch

Link to comment
Share on other sites

Yeah already checked the pedals and they are definately there :D getting really excited now!!!

Link to comment
Share on other sites

  • 2 weeks later...

Well just to let yous all know ive managed to get this activated on a 2010 1.6 focus. Turns out, according to the sneaky russians ;) ford decided to lock the software down to stop this but using older versions of the software sorts it out. So i downloaded a 2011 version and viola he now has cruise in his car

  • Like 1
Link to comment
Share on other sites

Well just to let yous all know ive managed to get this activated on a 2010 1.6 focus. Turns out, according to the sneaky russians ;) ford decided to lock the software down to stop this but using older versions of the software sorts it out. So i downloaded a 2011 version and viola he now has cruise in his car

Would it work on an ST?

Can it only be activated by a main dealer?

Link to comment
Share on other sites

In all honesty mate i couldnt tell you. Best bet is to check all wires above and if so should be able to activate it.

As for dealers, give em a ring and ask i know the ones up here will tell you to do one lol but if you dont ask you dont get lol

Link to comment
Share on other sites

I'll check the wires in the morning. Wish my car had cruise control.

Does it have to be the 2011 software? That could be a problem. Wish I was closer to you.

Link to comment
Share on other sites

Yeah it just has to be the earlier version to bypass the locks but after you can recalibrate to a new version ;)

Check wires and let us know if not sure get as many pics as you can and upload

Link to comment
Share on other sites

Mine doesn't have the wires :( Any chance just pulling the 2 wires straight from the steering to the plug will work ?

Link to comment
Share on other sites

You would need to check the fuse box to see if it has the connections available. Then you will need to get brake and clutch switches. Followed by wiring for all three - steering wheel, both switches.

Would be possible i bet but alot of work

Link to comment
Share on other sites

Excellent news John! sneaky Ford but you managed to hack it ;)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share





×
×
  • Create New...

Forums


News


Membership