Jump to content
Do Not Sell My Personal Information


Guide For Focus Mk2/mk2.5 C-Max/kuga ~Elm 327 Cable And Ff2 Program


Preee
 Share

Recommended Posts

I didn't manage to use ElmConfig, finally.

When I am trying to make the speed test on windows 7 i get the error from the picture (correct response from ELM timed. Received response to request "ATZ" : u).

post-42084-0-96056500-1364495411_thumb.j

When I am trying to make the speed test on windows XP, Elmconfic find ok all the speeds until 500.000 and then i had the error from this picture

post-42084-0-62948400-1364495635_thumb.j

and than the message from this one

post-42084-0-23626000-1364495640_thumb.j.

Do you have any other suggestions for me?

PS: I was trying also the EasyOBD software and it is working, all the led from Elm are blinking; I can connect to Obd and see that I have no DTC error and I can see live parameters, so is working somehow.

LE: Using checkChipVersion_v1006 software I found that I have a PL-2303HX / HXA chip, and on Prolific.com I found thah this chip are EOL and discontinued chips and there is a big possibility to be a counterfeit/fake PL-2303HX Rev A (or PL-2303HXA) USB-to-Serial Controller ICs using Prolific's trademark logo, brandname, and drivers, are being sold in the China market.

Link to comment
Share on other sites


I will give Negative to the seller because I can not use my Elm :(

Can you please tell my what version of Chip do you have?

You can use checkChipVersion_v1006 software from http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41

Thanks!

put up some pics of it .

Link to comment
Share on other sites

Hi guy's help needed with elmconfig i keep getting this error

component mscomm32.ocx or one of its dependencies not correctly registered a missing file or invalid.

Link to comment
Share on other sites

Hi guy's help needed with elmconfig i keep getting this error

component mscomm32.ocx or one of its dependencies not correctly registered a missing file or invalid.

On page one of this guide is a link to the Dll pack , required to install missing files that are not on your PC , download and run the install , if your on Win7 then run the install by right click and run as administrator. This will then fix your error

Link to comment
Share on other sites


Hi preee i have downloaded that file run as administrator installed then the last window says

yctahobka 3abepweha!

then i click ok but elmconfig still comes back with same error.

Link to comment
Share on other sites

What version of windows are you running 32 bit or 64 bit

Link to comment
Share on other sites

For W7 x64 users:

Here are the files:

http://www.mediafire.com/?mtyn7jm0qr8qels

Copy the four files to c:\windows\syswow64 , no need to copy the BAT file

Goto RUN command and type CMD and hit enter.

Black box will come on the screen

And than from the cmd register files:


regsvr32 c:\windows\syswow64\comdlg32.ocx
regsvr32 c:\windows\syswow64\MSCOMCTL.OCX
regsvr32 c:\windows\syswow64\mscomm32.ocx

regsvr32 c:\windows\syswow64\msvbvm60.dll

Link to comment
Share on other sites

Windows 7 x64, i will have ago and let you know.

Thanks again.

Link to comment
Share on other sites

Thanks for the help all up and running now.

Link to comment
Share on other sites

Good afternoon


I am Portuguese and I have a Focus 1.6 TDCI MK2.5 2008.


I upgraded the ROM 0230 to ROM 0509. Now instantaneous consumption is delayed, the hidden menu appears the error "nvm eeprom lvl 0001-Fail".

I've been to Ford and only resolved with a new panel.


Can I go back to the 0230 ROM?


Help me please


Sorry for my english

Link to comment
Share on other sites

Can anyone tell me which are the best drivers for an USB ELM so I can update my HEC to rom 0509?

I am using Windows XP 32bits and I tried to download the FTDI drivers from their website but Windows won't install the ELM with those drivers. I had to install it with Prolific drivers.

Once installed I made the speed test in ELM Config and all gave me OK result. But after test was over I couldn't enter with any speed. I had to unplug the ELM and close the Elm Config and started all again. The problem is that I can only enter with 38400 speed. No other option works....

Link to comment
Share on other sites

On this site you can find checkChipVersion_v1006 software and see what chip you have. If is PL-2303HX or HXA probably is fake like I had!

I couldn't manage to use it!

Link to comment
Share on other sites

Good afternoon
I am Portuguese and I have a Focus 1.6 TDCI MK2.5 2008.
I upgraded the ROM 0230 to ROM 0509. Now instantaneous consumption is delayed, the hidden menu appears the error "nvm eeprom lvl 0001-Fail".
I've been to Ford and only resolved with a new panel.
Can I go back to the 0230 ROM?
Help me please
Sorry for my english

Did you try to flash the ROM again ?

  • Like 1
Link to comment
Share on other sites

Did you try to flash the ROM again ?

Yes, twice.

Link to comment
Share on other sites


Good afternoon
I am Portuguese and I have a Focus 1.6 TDCI MK2.5 2008.
I upgraded the ROM 0230 to ROM 0509. Now instantaneous consumption is delayed, the hidden menu appears the error "nvm eeprom lvl 0001-Fail".
I've been to Ford and only resolved with a new panel.
Can I go back to the 0230 ROM?
Help me please
Sorry for my english

Why didn't they update the HEC to a later version? 0509 is not the latest version available...

The strange thing is that my HEC is on 0230 and also have that NVM EEPROM LVL 00001 FAIL but works fine... i think!

  • Like 1
Link to comment
Share on other sites

Why didn't they update the HEC to a later version? 0509 is not the latest version available...

The strange thing is that my HEC is on 0230 and also have that NVM EEPROM LVL 00001 FAIL but works fine... i think!

Have nothing to do with the ROM, has to do with going to page 3 of the HEC.

When i load the configuration on page 3 of the HEC appears a warning that can cause delayed on instant consumption, and I ignored. I think it is not only the immediate consumption, I also think that confuses autonomy and reserve warning light.

Link to comment
Share on other sites

Since activating my drive off door locks, I notice that when I stop the car, take the keys out and try to open mine / passenger door, the front doors unlock, but the rear doors dont!?

I have to then unlock twice (anti hijack) before I can actually get the kids out of the car...

Anybody have any idea's or seen this on there cars?

Link to comment
Share on other sites

Since activating my drive off door locks, I notice that when I stop the car, take the keys out and try to open mine / passenger door, the front doors unlock, but the rear doors dont!?

I have to then unlock twice (anti hijack) before I can actually get the kids out of the car...

Anybody have any idea's or seen this on there cars?

What about if you open the driver's door? If you pull the driver's interior lock just enought to unlock the door it should unlock all doors and boot.

Auto-lock should have nothing to do with the anti-hijack function! That you can activate/de-activate with you remote. Just keep near the car and press both lock and unlock buttons. After three seconds the indicators will flash and you should de-activate or activate the anti hijack. You can repeat the procedure and it will get to the former state.

Link to comment
Share on other sites

Cheers nuno, I think it must be just because I pull the handle rather than flick the lock... I am quite happy with the anti hijack, I just didnt know if there was a lesser known error with the combinations that stopped the doors unlocking properly.

Shame, as I liked the feature on my Kia which was remove key from barrel - all doors unlock...

Link to comment
Share on other sites

Actually having revisited this, if I sit in the car and pull the lock on the drivers door backover (it doesnt half take some tugging!) it still only unlocks my door, and the rest of the door locks point marginally inwards but not fully so...

Link to comment
Share on other sites

Push the lock button in and pull it out again, that should unlock all the doors.

Link to comment
Share on other sites

  • 2 weeks later...

Any updates i can make to my focus mk3 using this program ?

Link to comment
Share on other sites

Any updates i can make to my focus mk3 using this program ?

No but there is a program out there that you can use , but ! it's a program you have to pay for.

http://www.ucdsys.ru/

Link to comment
Share on other sites

No but there is a program out there that you can use , but ! it's a program you have to pay for.

http://www.ucdsys.ru/

Busy using it already.....arrived yesterday. So far so good !

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share





×
×
  • Create New...

Forums


News


Membership