Jump to content


Leemaxd

Member Since 25 Jul 2010
Offline Last Active Feb 20 2013 07:05 PM
*****

#202134 The Focus Zetec S Thread...

Posted by Leemaxd on 20 August 2012 - 06:38 AM

Here's mine.
Posted Image
Posted Image
Posted Image

Few random pics, not got any real recent ones.:)


#173279 Guide For Fitting Daytime Running Lights Focus Mk2.5

Posted by Leemaxd on 18 March 2012 - 09:49 PM

Cool they look well nice, we're they easy to fit ?


#173244 Guide For Fitting Daytime Running Lights Focus Mk2.5

Posted by Leemaxd on 18 March 2012 - 07:53 PM

Let us know how it goes fitting them drl's Lenny, this is something I wanna do next. :)


#157988 Guide Fitting St Gauge Pod To Focus Tdci Dash

Posted by Leemaxd on 25 December 2011 - 07:25 AM

Mines the 1.8 Lenny, I run a boost pipe into the engine bay and tapped into the map sensor tubing.
It peeks at about 1.8 bar on full boost.


#157973 Guide Fitting St Gauge Pod To Focus Tdci Dash

Posted by Leemaxd on 24 December 2011 - 10:44 PM

The pics are on here somewhere but here you go.
Posted Image


#157964 Guide Fitting St Gauge Pod To Focus Tdci Dash

Posted by Leemaxd on 24 December 2011 - 09:02 PM

I really enjoyed doing mine, the mess gets everywhere such a good feeling when it all pops into place :)


#157954 Merry Christmas Guys

Posted by Leemaxd on 24 December 2011 - 04:58 PM

Merry Christmas all :)


#156697 Thinking About Fitting St Gauge Pod In Focus Tdci

Posted by Leemaxd on 16 December 2011 - 06:58 AM

Well done mate, looking forward to seeing it all in and finished.


#147318 The Ultamate Rear Seat Cover

Posted by Leemaxd on 06 October 2011 - 05:47 PM

Exactly why I have just ordered one due to two young kids who love to make a great mess in the back. :)


#146777 Dash Storage

Posted by Leemaxd on 02 October 2011 - 07:28 PM

I used a sharp Stanley knife to first cut out the foam on top then underneath the foam is a hard plastic, I used a junior hacksaw blade to saw the plastic ( this was the best way to just gently do it and keep within the bowl).
The holes above the original clocks are the trickiest, I used a angle drill to drill upwards to get the holes as spot on as I could, again it doesn't matter much because the plastic on the unit covers up any mess.
The dials were super tricky, I removed the original three
dials completely and was left with an empty pod, brought two 52mm dials and had a housing to house them, unfortunately I didn't take any pics as I was doing them should of the amount of people that are asking me how I done it)
Hope this helps a bit.


#146747 Dash Storage

Posted by Leemaxd on 02 October 2011 - 05:38 PM

Cheers all, yea it takes a bit of guts to do but once you get stuck into it and make sure you keep within the bowl you can't go wrong really.


#128854 Dash Storage

Posted by Leemaxd on 25 May 2011 - 06:29 AM

No worries mark207, hope it helps other people if they wanna do it that's why I have put the pics up.


#128802 Dash Storage

Posted by Leemaxd on 24 May 2011 - 08:51 PM

I didn't fit the dash storage in the end, I fitted these

Posted Image

:)


#128796 Dash Storage

Posted by Leemaxd on 24 May 2011 - 08:25 PM

This is the mk2 dash there is a bowl you can cut out to fit it, the airbag is next to it.


#128756 Dash Storage

Posted by Leemaxd on 24 May 2011 - 05:59 PM

This is my car and that's my brother who is helping me fit it, there is a good guide that I went by to do it, it's not impossible at all it's just a bit tricky.