Jump to content



Member Since 11 Dec 2008
Offline Last Active May 09 2009 03:49 PM

Topics I've Started

mondeo engine from 1994 into 1995 fiesta

09 May 2009 - 03:48 PM

hi im just wondering if someone has allready done this im wanting to fit a 1.8 16v zetec engine from my old mondeo estate but need to know what i need to do this conversion as i have all the suspension, subframe etc etc from the mondeo as i just dropped it straight out of the bottom of the car so the engine with everything is still attached to the subframe. so bisically i need to know what engine mounts i need etc to fit my zetec engine into my fiesta mk2 1995 if anyone requires any info from me about the car or require any pics to help me out just pm me thanks


28 April 2009 - 08:31 AM

hi i have some mondeo 1994 estate MK 1 parts available these include,
4 x Doors 20.00 each 1 x door at 10.00 as the window winding cable has snapped so will need the cable changing but door in good condition,
Grey dash board 25.00,
heater Matrix 25.00 but will require a bit glueing to the rear nothing major,
origonal ford Radio+ casette with code 15.00
Door Seals 5.00 Each
Rear Wheel Bearings for non ABS Type with rear drums, was new 6 months ago hardly used as the cars been stood they retail at 80.00 from ford there is 2 available @ 25.00 Each
Front wheel bearing non abs type 15.00,
Front and Read seats will requre cleaning 50/00 for lot
if you require any pictures of the items please email me at mmafighterlinc@live.co.uk or PM me on here and all items are for collection only, postage is at extra cost and is for sale within the UK only thanks

need a mondeo engine 1.8 duratec he 16v please help

14 January 2009 - 03:49 PM

hi to anyone who reads this im after a mondeo 1.8 Duratec HE 16v Engine to fit my mondeo 2001 y reg i have tried everywhere round to where i live for an engine i would repair mine but have a hole in the side of the engine so if anyone just has the cylinder block without head or complete engine available i would be really really greatful if you could let me know i need my car really soon as i have got my mums wedding coming up and the car was supposed to be getting used for the wedding please please help!!

my ford mondeo mk3 1.8 HE duratec is dead

15 December 2008 - 01:49 PM

i bought this car a couple of days ago, from a car garage saying thats the car was in good condition but the engine was hard to start but did start but was rough, upon getting it home via recovery we started to do some checks to find the problem first of all we did a compression test and found this cylinders 1, 3, 4 had 200 psi of compression but cylinder 2 had zero compression by this we was puzzled, we then proceded to remove the rocker cover to see if it had dropped a valve on No. 2 cylinder we found nothing still puzzled by this, we thought for a while and then my mate turned the engine over and as i looked down cylinder 2 sparkplug hole i noticed the piston wasn't moving but all the others were!!!!. i then put all the top of the engine back toghter then moved onto removing the sump upon doing this i was shocked to what i found, the previous owner has revved the engine so hard the conrod on cylinder 2 has snapped and smashed a hole the size of 4 inches in length by an inch wide in the rear of the engine block and has also smashed the bracketing that holds the crankshaft and pistons in place, its lucky it only needs a new lower block as the top is ok, so be warned dont over rev your engine or this might happen to you.

mondeo mk3 engine problem

11 December 2008 - 10:53 PM

hi i have reciently bought this car, it has the duratec HE 1.8 SFI (125ps) engine in it, the problem is the car is very hard to start and when it does start its running on three cylinders could this be the head gasket thats gone and if it is how big a job is it to be fixed if not ford has mentioned it could be the coil pack.
there is no ECU light on thats saying its an electrical problem. please help as im baffled of what to do as one persons saying its one thing and another person is saying its some thing else many thanks