===PCM DTC P0693-60=== Code: P0693 - High speed fan output circuit malfunction - short to ground. Status (-60): - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Powertrain Control Module Diagnostic Trouble Code details High speed fan output circuit malfunction - short to ground. ===END PCM DTC P0693-60=== ===PCM DTC P0646-60=== Code: P0646 - Air conditioning clutch relay circuit short to ground. Status (-60): - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC Module: Powertrain Control Module Diagnostic Trouble Code details Air Conditioning Clutch Relay Control Circuit Low Ignore this DTC if the vehicle does not have AC fitted. This DTC may be caused by : Air conditioning clutch relay circuit short to ground. Open Circuit Air conditioning clutch ===END PCM DTC P0646-60=== ===PCM DTC P0341-E0=== Code: P0341 - CMP sensor signal implausible. Status (-E0): - DTC Present at Time of Request - Malfunction Indicator Lamp is On for this DTC Module: Powertrain Control Module Diagnostic Trouble Code details CMP sensor signal implausible. This DTC may be caused by : Camshaft Position (CMP) circuit performance. --Possible Causes-- - Harness routing. - Charging circuit. - Damaged CMP. - Damaged PCM. Note: Electrical noise detected. Incorrect base Cam timing. CMP sensor / wiring ===END PCM DTC P0341-E0=== ===PCM DTC P1000-70=== Code: P1000 - On-Board Diagnostic (OBD) Systems Readiness Test Not Complete Status (-70): - DTC Present at Time of Request - Malfunction Indicator Lamp is Off for this DTC - Test not complete Module: Powertrain Control Module Diagnostic Trouble Code details On-Board Diagnostic (OBD) Systems Readiness Test Not Complete Follow the routines in the service manual to resolve the DTC listed. ===END PCM DTC P1000-70=== ===OBDII DTC None=== Successful DTC reading, no error codes found Module: On Board Diagnostic II ===END OBDII DTC None=== ===IC DTC None=== Successful DTC reading, no error codes found Module: Instrument Cluster ===END IC DTC None=== ===RCM DTC B2232=== Code: B2232 - Air Bag Circuit Open - Loop #2, Front Driver side Module: Restraint Control Module ===END RCM DTC B2232=== ===RCM DTC B1318=== Code: B1318 - The battery voltage level is too low. Module: Restraint Control Module Diagnostic Trouble Code details Battery Voltage Low This DTC may be caused by : Check fuses. Power supply to fuse Discharged or faulty battery. Check the condition of the battery. Check the battery charging system. Check the connector for damage or contamination. Check the connectors and wiring harness for damage or contamination. Check the wiring and the appropriate fuse. High resistance in wiring ===END RCM DTC B1318=== ===GEM DTC None=== Successful DTC reading, no error codes found Module: Generic Electronic Module ===END GEM DTC None=== ===ABS DTC C1235=== Code: C1235 - Right Rear Wheel Speed Sensor Input Signal Missing Module: Antilock braking system Diagnostic Trouble Code details The right rear wheel speed sensor input signal missing or the signal is not plausible. The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set. A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows: Damaged wheel speed sensor. Sensor air gap too large. The vehicle has been towed on two wheels. A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off. The vehicle has been driven on a two wheel rolling road. There is a short duration intermittent open circuit on the sensor wiring. The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.) The tires installed have varying outside diameters. A wheel bearing is worn or loose. ===END ABS DTC C1235=== ===ABS DTC C1236=== Code: C1236 - Left Rear Wheel Speed Sensor Input Signal Missing Module: Antilock braking system Diagnostic Trouble Code details The left rear wheel speed sensor input signal missing or the signal is not plausible. The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set. A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows: Damaged wheel speed sensor. Sensor air gap too large. The vehicle has been towed on two wheels. A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off. The vehicle has been driven on a two wheel rolling road. There is a short duration intermittent open circuit on the sensor wiring. The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.) The tires installed have varying outside diameters. A wheel bearing is worn or loose. ===END ABS DTC C1236=== ===ABS DTC C1233=== Code: C1233 - Left Front Wheel Speed Sensor Input Signal Missing Module: Antilock braking system Diagnostic Trouble Code details The left front wheel speed sensor input signal is missing or the signal is not plausible. The code is set normally when the speed from one sensor differs from the speed on the other three sensors. The vehicle speed must exceed 40 kph (25 mph) for this code to be set. A fault has been reported. At some time a wheel speed signal has been out of range. The possible causes are as follows: Damaged wheel speed sensor. Sensor air gap too large. The vehicle has been towed on two wheels. A road wheel has been dynamically balanced on the vehicle while the IN2IGN iwas in position II or shortly after IN2IGN off. The vehicle has been driven on a two wheel rolling road. There is a short duration intermittent open circuit on the sensor wiring. The vehicle has been accident damaged or abused (eg. rolled spun parking brake turns etc.) The tires installed have varying outside diameters. A wheel bearing is worn or loose. ===END ABS DTC C1233===