===OBDII DTC P0443-C=== Code: P0443 - Purge valve circuit fault Status: - Confirmed - malfunction is confirmed Module: On Board Diagnostic II ===END OBDII DTC P0443-C=== ===IC DTC U1262=== Code: U1262 - SCP Data Link Fault Module: Instrument Cluster Diagnostic Trouble Code details SCP Data Link Fault Operator Action Run self test. All CMDTCs Fix all relevant DTCs then clear codes and retest. Note: DTCs that start with 'U' are faults which occur during module-to-module communication. Modules should never be replaced based only on a 'U' code. These codes do not always indicate a problem, and can be caused by normal diagnostic functions, carried out on the vehicle. ===END IC DTC U1262=== ===PCM DTC P0460=== Code: P0460 - Invalid fuel tank level message from instrument cluster. Module: Powertrain Control Module Diagnostic Trouble Code details Invalid fuel tank level message from instrument cluster. This DTC may be caused by : Fuel sender circuit failure Faulty or damaged instrument cluster module. Run the insrument cluster diagnostics ===END PCM DTC P0460=== ===PCM DTC P0113=== Code: P0113 - IAT Sensor Circuit High Input Module: Powertrain Control Module Diagnostic Trouble Code details IAT Sensor Circuit High Input This DTC may be caused by : Open Circuit Signal shorted to VBATT or vref. Sensor Previously disconnected. Faulty Sensor Faulty or damaged PCM. Extreme low ambient temperature. Improper connection Incorrect VREF. SIGRTN open circuit ===END PCM DTC P0113=== ===PCM DTC P0602=== Code: P0602 - PCM programming error Module: Powertrain Control Module Diagnostic Trouble Code details PCM programming error Follow the routines in the service manual to resolve the DTC listed. ===END PCM DTC P0602=== ===PCM DTC P0174=== Code: P0174 - System Too Lean Bank 2 Module: Powertrain Control Module Diagnostic Trouble Code details System Too Lean Bank 2 The PCM monitors the adaptive fuel table to ensure fuel control system components do not vary from their nominal values. The fuel control strategy within the PCM uses the adaptive fuel table to compensate for normal wear or aging of fuel control system components. The code is set when the PCM can no longer compensate for additional changes in the fuel system. This DTC may be caused by : Suspect Low fuel pressure. Crankcase Ventilation System Suspect air intake system leak. Suspect engine vacuum leak. Suspect HO2S21 circuit. Suspect PCM. A blocked fuel filter will restrict the flow of fuel to the pressure regulator. If the fuel supply to the fuel filter is O.K. the fuel filter may be blocked. Obstructed or dirty fuel injector(s) Suspect EVAP EVAP canister purge solenoid. Leaking exhaust system. ===END PCM DTC P0174=== ===PCM DTC P0443=== Code: P0443 - Purge valve circuit fault Module: Powertrain Control Module ===END PCM DTC P0443=== ===MC DTC B1318=== Code: B1318 - Battery voltage Low Module: Message Center ===END MC DTC B1318=== ===ECS DTC B1994=== Code: B1994 - Side Air Bag Circuit Open, Front Driver Side Module: Electronic Crash Sensor Diagnostic Trouble Code details Side Airbag Open Circuit (Drivers) ===END ECS DTC B1994=== ===ECS DTC B1877=== Code: B1877 - Safetybelt Driver Retractor Circuit Failure Module: Electronic Crash Sensor Diagnostic Trouble Code details Safetybelt Driver Retractor Circuit Failure --- Possible Causes -------- -Seatbelt Driver Pretensioner Circuit Failure -Check for: -Open Circuit -Short to Battery/Gnd -Faulty switch/module Driver safety belt pretensioner resistance is too high Wiring Harness Open Circuit Please Check Connections High resistance in wiring ===END ECS DTC B1877=== ===ECS DTC B1318=== Code: B1318 - Battery voltage Low Module: Electronic Crash Sensor Diagnostic Trouble Code details Battery Voltage Too Low --- Possible Causes -------- - Battery Voltage below 9.6volts -Suspect Battery state of charge Charging system ===END ECS DTC B1318=== ===CTM DTC B1244=== Code: B1244 - Rear Windshield Wiper relay circuit failure Module: Central timer module Diagnostic Trouble Code details Rear Windshield Wiper relay circuit failure Possible Causes The hardware detects an open circuit or a short to ground. suspect relay Suspect the module that generated this code. ===END CTM DTC B1244=== ===CTM DTC B2256=== Code: B2256 - Heated windshield relay short to ground Module: Central timer module Diagnostic Trouble Code details Heated windshield relay short to ground Gem module pin EN23 (C426;Blue) ===END CTM DTC B2256=== ===CTM DTC B1428=== Code: B1428 - Safety belt lamp circuit failure Module: Central timer module Diagnostic Trouble Code details Safety belt lamp circuit failure --- Possible Causes -------- This code can be generated by: -Ground Short Driver's Seat Belt Lamp -Open Driver's Seat Belt Lamp -Suspect Driver's Seat Belt Lamp -Suspect Generic Electronic Module ===END CTM DTC B1428=== ===ABS DTC None=== Successful DTC reading, no error codes found Module: Antilock braking system ===END ABS DTC None===