gillyallan Posted June 30, 2021 Share Posted June 30, 2021 Just wish the website wouldn't say. You'll be please to know.... I'm not pleased, gimmie the update. Quote Link to comment Share on other sites More sharing options...
SgtAWilson Posted July 21, 2021 Share Posted July 21, 2021 On 6/30/2021 at 5:16 PM, gillyallan said: Just wish the website wouldn't say. You'll be please to know.... I'm not pleased, gimmie the update. Do we know if the F10 maps have been released yet for Sync 3 V3.0? Quote Link to comment Share on other sites More sharing options...
Andyr55 Posted July 22, 2021 Share Posted July 22, 2021 Not sure any updates are available for sync3. Quote Link to comment Share on other sites More sharing options...
Sneezy24 Posted July 27, 2021 Share Posted July 27, 2021 Well, it seemed to be working, just very slowly. Appearing to do little bits every time I drove. Then wife drove it - claims she didn't touch anything, but I now get the dreaded MEM_ERR01 (or ERR_MEM01). Ho hum, perhaps I'll manage without F10!!!!! Thinking of the CyanLabs route, does it take the same length of time? and the same pallaver? Does the Ford Interrogator prog. give results that Ford accept?? Quote Link to comment Share on other sites More sharing options...
gillyallan Posted August 12, 2021 Share Posted August 12, 2021 I check often the sync update site and today it's saying a map update but says 0mb. This is for a 17plate 3.5 model on sync 3.0 Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 13, 2021 Share Posted August 13, 2021 Just installed the 0mb map update and uploaded the log file on the Ford website. Doesn't seem to have done anything and the Ford site is still offering me the same 0mb update. Has anyone else got the same thing? Quote Link to comment Share on other sites More sharing options...
Mark-UK Posted August 13, 2021 Share Posted August 13, 2021 On 7/27/2021 at 3:28 PM, Sneezy24 said: Well, it seemed to be working, just very slowly. Appearing to do little bits every time I drove. Then wife drove it - claims she didn't touch anything, but I now get the dreaded MEM_ERR01 (or ERR_MEM01). Ho hum, perhaps I'll manage without F10!!!!! Thinking of the CyanLabs route, does it take the same length of time? and the same pallaver? Does the Ford Interrogator prog. give results that Ford accept?? At least Ford are honest about MEM-ERRO1 The haven't got a clue, this is from the fortnightly email I've been getting for a while now "Again I have heard back from our technical team in regards to the issue, they have informed me the matter is still under investigation and it is still their top priority. Unfortunately they are still unsure as the route of the issue but are working on it." Quote Link to comment Share on other sites More sharing options...
unofix Posted August 13, 2021 Share Posted August 13, 2021 On 7/27/2021 at 3:28 PM, Sneezy24 said: Thinking of the CyanLabs route, does it take the same length of time? and the same pallaver? Does the Ford Interrogator prog. give results that Ford accept?? I've been using CyanLabs for about the last 10 months and used them to do all the map updates. It still takes some time but is way quicker than Ford. You stick in the USB which the Cyanlabs configured and away you go. It loads - it updates - it works !! what more could you want ? 1 Quote Link to comment Share on other sites More sharing options...
Mark-UK Posted August 13, 2021 Share Posted August 13, 2021 When I first got the MEM-ERRO1 , I went back on the ford download site and there was still a small map update left, this would never install, told Ford and have just left it at that. Parked the car this morning and it said downloading update (via wifi) Went back on the ford site and I'm fully up to date, god knows what's actually happening. So website says no updates but car say downloading, and it looks like it'll take a while . Quote Link to comment Share on other sites More sharing options...
unofix Posted August 13, 2021 Share Posted August 13, 2021 Ford are not the only ones with software bugs- Microsoft have a severe security threat (windows 10) allowing hackers to take control of your PC when you print. Microsoft haven't got a fix for this yet !! Universities are disabling all printing for the forseeable time untill a fix or work around can be found. Quote Link to comment Share on other sites More sharing options...
Mark-UK Posted August 13, 2021 Share Posted August 13, 2021 There must be more people complaining about the MEM-ERRO1 as my fortnightly email just jumped to 2 this week 10 August Again I have heard back from our technical team in regards to the issue, they have informed me the matter is still under investigation and it is still their top priority. Unfortunately they are still unsure as the route of the issue but are working on it. I look forward to contacting you again soon with an update. 13 August I hope you are well. Just wanted to update you in regards to the issue and let you know our technical are looking deeper into this matter and it should be resolved soon. I'm expecting the next one to say, We have done a deal with CyanLabs and the reformat reinstall software is now available to download from Ford 🤣 2 Quote Link to comment Share on other sites More sharing options...
gillyallan Posted August 13, 2021 Share Posted August 13, 2021 5 hours ago, AB100 said: Just installed the 0mb map update and uploaded the log file on the Ford website. Doesn't seem to have done anything and the Ford site is still offering me the same 0mb update. Has anyone else got the same thing? Tried earlier. It did say updating but never gave any complete that previous updates have done. Also nothing has changed. I'm waiting my son checking usb stick to see if at least a log file has been generated. Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 13, 2021 Share Posted August 13, 2021 41 minutes ago, gillyallan said: Tried earlier. It did say updating but never gave any complete that previous updates have done. Also nothing has changed. I'm waiting my son checking usb stick to see if at least a log file has been generated. I didn’t see the ‘complete’ when I ran the update but I left the usb stick in and did a key cycle, then got the complete message and it downloaded the log file. Quote Link to comment Share on other sites More sharing options...
gillyallan Posted August 13, 2021 Share Posted August 13, 2021 26 minutes ago, AB100 said: I didn’t see the ‘complete’ when I ran the update but I left the usb stick in and did a key cycle, then got the complete message and it downloaded the log file. Ok. Went back out put usb in and started up. Got a brief system update then said it was complete. I've uploaded log file. Will see if any change over next few days Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 17, 2021 Share Posted August 17, 2021 I got fed up waiting for the Ford web site to change, so I downloaded the file provided under "troubleshooting" to generate a new log file. Said it would take around 1 minute to run. When I put it in the car I got the "updating software message" 20 minutes later it wast still saying that. At that point I gave up and removed the usb stick from the car. It has generated a file called "utloggingutility.Interlog_utility.log" but that won't upload onto the Ford site as its not an XLS file. Not sure what to do now? Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 17, 2021 Share Posted August 17, 2021 On 8/13/2021 at 7:32 PM, gillyallan said: Ok. Went back out put usb in and started up. Got a brief system update then said it was complete. I've uploaded log file. Will see if any change over next few days I got fed up waiting for the Ford web site to change, so I downloaded the file provided under "troubleshooting" to generate a new log file. Said it would take around 1 minute to run. When I put it in the car I got the "updating software message" 20 minutes later it wast still saying that. At that point I gave up and removed the usb stick from the car. It has generated a file called "utloggingutility.Interlog_utility.log" but that won't upload onto the Ford site as its not an XLS file. Not sure what to do now? Quote Link to comment Share on other sites More sharing options...
YOG Posted August 17, 2021 Share Posted August 17, 2021 On 8/13/2021 at 1:59 PM, unofix said: I've been using CyanLabs for about the last 10 months and used them to do all the map updates. It still takes some time but is way quicker than Ford. You stick in the USB which the Cyanlabs configured and away you go. It loads - it updates - it works !! what more could you want ? I have an ST3 2016, which I upgraded from SYNC 2 to SYNC 3. I have used Cyanlabs for all my updates, from SYNC 3, software version: 3.0 Build 19205 (Navigation F9) to the latest SYNC 3, software version: 3.4 Build 21194 (Navigation F10). After the install of Build 21194, I had the No GPS logo (like a no entry road-sign) appear on the Nav screen. It remained, even after a Master Reset. I carried out a reinstall of the previous 21098 (Navigation F10), and everything is back to working fine. 2 Quote Link to comment Share on other sites More sharing options...
unofix Posted August 17, 2021 Share Posted August 17, 2021 1 hour ago, YOG said: I carried out a reinstall of the previous 21098 (Navigation F10), and everything is back to working fine. Good infromation, so it looks like this is the most up to date working version and that 21194 should not be used. Quote Link to comment Share on other sites More sharing options...
devil71 Posted August 17, 2021 Share Posted August 17, 2021 3 hours ago, unofix said: Buone informazioni, quindi sembra che questa sia la versione funzionante più aggiornata e che 21194 non dovrebbe essere usato. Cyanlabs.com download 1 Quote Link to comment Share on other sites More sharing options...
Sneezy24 Posted August 18, 2021 Share Posted August 18, 2021 Going to try the Cyan Labs route on the next longish run. Preping the USB stick at the moment. Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 18, 2021 Share Posted August 18, 2021 On 8/17/2021 at 3:40 PM, AB100 said: I got fed up waiting for the Ford web site to change, so I downloaded the file provided under "troubleshooting" to generate a new log file. Said it would take around 1 minute to run. When I put it in the car I got the "updating software message" 20 minutes later it wast still saying that. At that point I gave up and removed the usb stick from the car. It has generated a file called "utloggingutility.Interlog_utility.log" but that won't upload onto the Ford site as its not an XLS file. Not sure what to do now? Returned to car this afternoon and put the memory stick back in. Within a few seconds got the "update complete" message and it downloaded the log file correctly. Just uploaded that on the Ford site, will see if it makes any difference. Quote Link to comment Share on other sites More sharing options...
SgtAWilson Posted August 18, 2021 Share Posted August 18, 2021 I too have noticed the 0mb download file for my 2017 Focus. However, im presuming this is just a Ford website issue, so will be interested to see if it does actually do anything. Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 23, 2021 Share Posted August 23, 2021 On 8/18/2021 at 7:14 PM, SgtAWilson said: I too have noticed the 0mb download file for my 2017 Focus. However, im presuming this is just a Ford website issue, so will be interested to see if it does actually do anything. See my previous posts above. Having messed around with installing the 0gb update it’s now offering me a 24gb one. Will download it later Quote Link to comment Share on other sites More sharing options...
AB100 Posted August 23, 2021 Share Posted August 23, 2021 2 hours ago, AB100 said: See my previous posts above. Having messed around with installing the 0gb update it’s now offering me a 24gb one. Will download it later Now there appears to be a an issue getting updates downloaded from the Ford site. Used the chat facility and was told it is a known issue and I should try agin in a few day. You'd think someone would have the sense to put a message to that effect on the page! Quote Link to comment Share on other sites More sharing options...
Mark-UK Posted August 26, 2021 Share Posted August 26, 2021 I've been dealing with Ford for several weeks over the MEM-ERRO1 issue, got an email today saying there's nowt they can do, take it to a dealer. Well I'm not paying for them to sort it out, so Cyanlabs here I come. Quote Good Morning Mr S, I hope you are keeping well. Unfortunately, our internal technical specialist has decided to leave the company for a different position and at this stage, we do not have the assistance of an internal technician. As we are not technically nor mechanically trained within the customer relationship centre, we do now have to recommend that you book your vehicle in at a Ford Dealership for them to review the concerns with your system and apply any outstanding updates. We are very sorry for any frustration and inconvenience that this may cause, however with the dealership being able to physically review the concern first hand, we are confident that this will now be the most efficient route to resolve the concerns. Please could you arrange for the vehicle to be booked in to a Ford dealership and provide us with the date, time and dealership chosen so we can liaise with them when the vehicle is on site. I will touch base by Wednesday Afternoon at the latest (01/09) to gain these details and review to assist you further. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Ford UK Shop
Sponsored Ad
Name: eBay
Ford Model: FordUK Shop
Ford Year: 2024
Latest Deals
Ford UK Shop for genuine Ford parts & accessoriesDisclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.