jeebowhite Posted December 4, 2013 Share Posted December 4, 2013 I think it only takes effect if it is successful, if it fails and you reset it, it should go back to where it was. Quote Link to comment Share on other sites More sharing options...
HotAction Posted December 4, 2013 Share Posted December 4, 2013 I have disconnected the battery for 10 minutes. Connected it again but the cluster is still death But the turn signals are flashing all the time! When i Try to programm the rom level again he will show me that... file:///C:/Dokumente%20und%20Einstellungen/Administrator/Desktop/fehler.bmp Quote Link to comment Share on other sites More sharing options...
HotAction Posted December 4, 2013 Share Posted December 4, 2013 Sorry I dont know how i can post a picture of the failure :( Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 4, 2013 Share Posted December 4, 2013 you would need to upload your picture to the internet and then link to it. Did you take a backup of the ROM at all? If you have a look through this post there should somewhere be a link to some firmware, you might want to try and load another firmware version? Quote Link to comment Share on other sites More sharing options...
HotAction Posted December 4, 2013 Share Posted December 4, 2013 Hope this picture will work. No i dont think that i have done that. I only save the config pages...If I found the correct Firmeware how can i Implement them with my elm? I'm not as familiar with the elmconfig software Sorry but I get the elm only one day ago . Do you know which page number i can find the Firmewares? Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 4, 2013 Share Posted December 4, 2013 Swen, have a look at this in particular: http://www.fordownersclub.com/forums/topic/31287-guide-for-focus-mk2mk25-c-maxkuga-elm-327-cable-and-ff2-program/?view=findpost&p=278064 It looks like you might be able to download the firmware from here: http://www.motorcraftservice.com/vdirs/wds/PCMReprogram/DSFM_PCMReprogram.asp?swproduct=IDS Quote Link to comment Share on other sites More sharing options...
HotAction Posted December 4, 2013 Share Posted December 4, 2013 James, If I understand you correct i Should update the PCM? would this solve my problem? Quote Link to comment Share on other sites More sharing options...
HotAction Posted December 4, 2013 Share Posted December 4, 2013 short feedback :) Everything is working again B) The Problem was my old Laptop, which I usually use for Elmconfig, was to slow for that kind of update. I changed to my new one and everything worked again. Now I have got the ECO Mode on my Focus RS. I never see that it will work on the RS. Now I have to wait until march to test everything, but I hope everything will work now?Maybe the shift up indicator also. @James, Thank you very much for your help and fast support! Best Regards Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 4, 2013 Share Posted December 4, 2013 Swen, Glad to hear that all is well! one day I will try and see if I can do the update! Quote Link to comment Share on other sites More sharing options...
mondeo zetec Posted December 13, 2013 Share Posted December 13, 2013 is there a english edited version of elm config for the mondeo mk4 etc...??? i cannot find it any where thank's Quote Link to comment Share on other sites More sharing options...
mondeo zetec Posted December 13, 2013 Share Posted December 13, 2013 /and does the elm ff2 program not work with a 500000 baud elm lead..? Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 13, 2013 Share Posted December 13, 2013 Hi Sean, Check the link on the first page, the software has come on leaps and bounds and now has full english support :) as for the FF2, I dont believe that it supports the 500,000 but thats because I dont believe it can access that area of the car. Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 16, 2013 Share Posted December 16, 2013 OK, so I have trawled all 116 pages, and have not seen this error yet! I bought a 500000 cable from Dez and used it to read the VIN at top speed from the GEM page 2. It read the VIN fine, however, when I try to download the data, I get the following error: Incorrect response from ELM to request "22 09 DF"; 7F 22 31 31 - Request out of range It seems to read other things alright, but wont let me download so that I can enable the integrated speed control.... Anyone got any thoughts? Quote Link to comment Share on other sites More sharing options...
jpinhas Posted December 17, 2013 Share Posted December 17, 2013 Anyone know if it is already possible to reverse the delay instant consumption, caused by the upgrade Trip Computer for ROM 0509. In the latest version of Elmconfig is now possible to update the range of instantaneous consumption. I changed to 12, but do not know if it is correct. The error "NVM EEPROM FAIL LVL 00001" disappeared, and the instantaneous consumption is faster to update. Quote Link to comment Share on other sites More sharing options...
mayak Posted December 17, 2013 Share Posted December 17, 2013 In the latest version of Elmconfig is now possible to update the range of instantaneous consumption. I changed to 12, but do not know if it is correct. The error "NVM EEPROM FAIL LVL 00001" disappeared, and the instantaneous consumption is faster to update. Autor of ELMConfig suggest to change to 5 - I had 63 (maximum!), but now I have 5 :) Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 17, 2013 Share Posted December 17, 2013 OK, so I have trawled all 116 pages, and have not seen this error yet! I bought a 500000 cable from Dez and used it to read the VIN at top speed from the GEM page 2. It read the VIN fine, however, when I try to download the data, I get the following error: It seems to read other things alright, but wont let me download so that I can enable the integrated speed control.... Anyone got any thoughts? In Case anyone should come across this as useful information, I found the issue. I set the PCM incorrectly! I set it to 1.6 TDCI and success! I can read! However, It seems that no matter which PCM I use, none are supported :( This is under all of the PCM types as well, so its the same error on the others :( I have connected the switches temporarily and will try it on my way home tonight (who knows, miracles might happen!) however, it seems that I wont be able to do this with Elm Config perhaps. Do we have any contact details or a means of reaching out to Civil ZZ? I know he doesnt come here these days...? Quote Link to comment Share on other sites More sharing options...
Tezza Posted December 17, 2013 Share Posted December 17, 2013 In the latest version of Elmconfig is now possible to update the range of instantaneous consumption. I changed to 12, but do not know if it is correct. The error "NVM EEPROM FAIL LVL 00001" disappeared, and the instantaneous consumption is faster to update. Is there a link to the latest version please Mayak Still had no response in the UCDS adaptor :( Quote Link to comment Share on other sites More sharing options...
dezwez Posted December 17, 2013 Share Posted December 17, 2013 Is there a link to the latest version please Mayak Still had no response in the UCDS adaptor :( here you go http://civil.iffc.ru/ELMConfig/ Quote Link to comment Share on other sites More sharing options...
Tezza Posted December 17, 2013 Share Posted December 17, 2013 Thanks mate your a star :) Quote Link to comment Share on other sites More sharing options...
jpinhas Posted December 17, 2013 Share Posted December 17, 2013 Autor of ELMConfig suggest to change to 5 - I had 63 (maximum!), but now I have 5 :) 5 is not very fast? Quote Link to comment Share on other sites More sharing options...
Mininu Posted December 27, 2013 Share Posted December 27, 2013 Hi. Can someone please tell me how can i pair a new(used) instrument cluster(mk2.5 model) on a mk2 focus? Thank you. Quote Link to comment Share on other sites More sharing options...
jeebowhite Posted December 27, 2013 Share Posted December 27, 2013 You would need the Ford IDS software system. it cannot be done without it. Quote Link to comment Share on other sites More sharing options...
dezwez Posted December 27, 2013 Share Posted December 27, 2013 now fitted my four spoke steering wheel and got cruse control on a mk 2.5 zetec 1.8 petrol well pleased Quote Link to comment Share on other sites More sharing options...
TDCiST Posted December 27, 2013 Share Posted December 27, 2013 Great news Dezwez! I just need to find a steering heel and associated bits now!! Quote Link to comment Share on other sites More sharing options...
Stoney871 Posted December 27, 2013 Share Posted December 27, 2013 http://pages.ebay.com/link/?nav=item.view&id=121224814111 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.