Jump to content
Do Not Sell My Personal Information


MH83

Budding Enthusiast
  • Posts

    10
  • Joined

  • Last visited

Profile Information

  • First Name
    Marius
  • Ford Model
    Mondeo Mk5 2.0 TDCi AWD Manual
  • Ford Year
    2016
  • UK/Ireland Location
    Other/NonUK

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

MH83's Achievements

  1. Just wanted to thank everyone for the help so far, but I have yet another update. Got hold of a second hand pump from a scrap dealer, the pump's got about 75k miles on it. Got the thing installed, and it fired up on the second go. It was a bit rough - ran fine at a bit higher revs, but figured that was because I hadn't connected up the MAF yet. So, put everything back; and it's still idling rough. It also started giving me a dash warning about low engine oil pressure. So I tried reading the codes to see what was up, and it gives me nothing related to oil pressure, but I get a P0266 error. P0266 - cylinder 2 contribution/balance (see photos). I've tried running a live readout on the only thing in the PCM I could find related to the injectors, which was the injector offsets. No idea if these are related though. Anybody care to take a guess?
  2. Okay, I finally figured it out... 🤦‍♂️ Pump shaft broke 🙄 Didn't actually think it would be such a catastrophic failure, but here we are I guess. At least I'm done fault checking. Now I just got to get a hold of a new one without having to bankrupt myself 😝
  3. Yes, and thanks a lot, guys 🙂 Thru the power of Google I managed to do a leak off test, and there is no leak. In fact, no diesel made it to the injectors at all. Not a drop. So with no measurable pressure from the sensor as well, everything points towards a faulty pump, either the spring or the regulator. When FIL gets back from his camping trip we're gonna crack it open like Alan showed in his video and take a look at that spring. It should be easy enough be able to get it out without removing the pump.
  4. Since my code reader is not giving me any info (apart from a 0.49v reading), I guess we can try reading the sensor directly. Found some guides on how to connect some y-splitters in order to measure the actual voltage. Seeing as the I get a FP error when I disconnect the supply line, I would assume the sensor is not entirely broken. I've managed to cobble together a leakoff kit, but haven't had the time to run the test yet. @Tizer, these are what I could figure was the relevant sensors for the fuel pressure. The only ones that are giving me anything, is the commanded pressure and the voltage, and that seems to be way to low. The mechanic I spoke with also suggested the sensor, but I'm not sure anymore. It does briefly start if you give it a little squirt of starter gas directly, but it's not able to keep going. So at least there is compression there, and it's getting air, so at least it's narrowed down to a fuel supply issue, but we've sort of already figured as much. I've also heard from another forum that it could be the fuel pressure regulator (pressure control valve).
  5. Oh, and @nicam49, I'd be most grateful for some instructions, please, thank you 🙂
  6. Okay, so I tried monitoring the frp while cranking, but I'm not able to make heads or tails of what I'm seeing. I really don't know quite what I'm looking at, but I took a couple of screenshots, so maybe you guys can decipher it for me 🙂 None of the graphs aren't giving much of a response, and there's no indication of any spikes in pressure, which I'd assume it should.
  7. Yeah, I tried that, but I'm not sure which sensor I should watch. There were several sensors with almost the same name, and a total of like 10 or something sensors related to the fuel pressure sensor (several that measure bar and a few that measure voltage). I don't have the name for them right now, but I'll check tomorrow and post the sensors' names, so you guys hopefully know which one I should watch. Thanks 🙂
  8. Update! Sorry for the late reply, RL got in the way, like it does sometimes. I've got the FORScan scanner and software, and ran a diagnostic. Since the dude that helped, erased the PCM errors, I've tried running it again, and I get no codes what so ever. I got some help from my FIL, and we changed both the fuel filter, and the air filter, just to be sure that there were no blockages. Fired up FORScan, erased all codes again (even though there were none) - just to be sure - and ran a diagnostic again. Still nothing. So we disconnected the line running to the rail and tried cranking it, and plenty of diesel gushed out. Like, ALOT. So I would assume the high pressure pump is not broken. After running a diag again, I now got the P0087 error (low fuel pressure). Erased the code, reconnected the hose, and cranked it, and it is not reporting this error again, so by my logic, the fuel pressure sensor works, and there is enough fuel getting to the system. What baffles me, is that there were no warnings before any of this happened. No rough idling, no sputtering, no problems starting, no reduced power, no rattling or noise, everything was just tip top. And it just suddenly cut out. We've checked all the fuses, they're not broken, the cams turn - they appears to be chain driven, not belt - so it's not a matter of a slipping belt. In my mind, seeing as the fuel is there, with what seems to be enough pressure, it's getting air, it must be either a compression issue or an electronics issue. I've read that the BCM could be faulty, but would that not result in an errorcode, or failure to read said module? I have not done a leak-off test, but according to what I've found, it should still be able to run even if they leak too much, and also would give the above mentioned P0087 error, as it is unable to maintain pressure. I find it hard to believe that all 4 injectors have gone bad at the same time, all valves are stuck open, all valve-lifters have broken, or that the head gasket is suddenly so broken that none of the cylinders have any compression what so ever. Because there is simply no indication of any ignition at all. It's like there were no fuel in the tank (it is, and it's only diesel). I am at a loss. I would like to not have to take it to a shop, because $$$, but I might have to 🙁 Thanks for any and all replies.
  9. We did that, and it gave no codes when we tried again after a few cranks. But his code reader was an universal type, so I'm not sure if it can read them all, or take live data. I've order a ForScan compatible scanner, so hopefully I can get a more specific readout, hopefully. It should be here within a couple of days, I'll try again and I'll post the results, if any. Saw a video about the pressure thing; I really hope that it's not the pump 😬 Thanks for the response so far 🙂
  10. Welcome to Ford Owners Club - Ford Forums. Please feel free to browse around and get to know the others. If you have any questions please don't hesitate to ask.

  11. Mondeo Mk5, 2.0 TDCi 4x4, 189.000km (~115k miles), Norway The other day, while I accelerated onto the highway, just as I hit 80km/h (50mph), the dreaded amber spanner lit up, and I lost engine power. It didn't cut completely out, but I was unable to accelerate or maintain speed. As I came to a halt on the shoulder, the engine stopped, and the spanner went away, being replaced by the CEL. The car now won't start. It cranks, but it won't start. Having ever only had- and worked on- petrol cars, I have limited experience with diesels, but I know the basics, and cranking but not starting is in my mind related to either fuel, air or compression. After I got home, I got a guy I know to come and read the codes, and we found the following: P228C(00) - Fuel pressure regulator 1, control limit exceeded - fuel pressure low P0087(00) - Fuel rail/system pressure to low P02FA(99) - Diesel intake airflow position sensor - minimum/maximum stop performance He had never worked on Mondeos, but he knew a mechanic, and gave him a call. Before he could finish telling him all the symptoms, the guy just responded with "Fuel pressure sensor, 100% sure, common on these cars". Is it this simple? 'Cause this part I can get easily enough from Autodoc or similiar (as soon as they're back in stock), or a scrap-dealer for less than £100. Ford would only sell me the entire rail, and that costs like 4 times that. I've tried googling it, and the list of possible errors related to a specific code, is in the best of cases, very general; it could apparently be a plethora of things, among them, the fuel pressure sensor. I've also heard it could be the DPF, fuel regulator, high-pressure pump, feed pump etc. (hope it's not though, those are expensive). There are no visible leaks, nor any smell of diesel, so I'm guessing it's not a leak anywhere. The guy with the code reader, said to me he could feel the flow in the lines to the rail (I'm assuming this is possible due to the high-pressure pump), so I assume the diesel is reaching the rail. However, I would like to get a second opinion, as well. If any of you have any insight or experience with this kind of fault, I'd be very grateful. Thanks
×
×
  • Create New...

Forums


News


Membership