Jollyandy

FOC Supporters
  • Content Count

    159
  • Joined

  • Last visited

1 Follower

About Jollyandy

  • Rank
    Feet Under The Table

Profile Information

  • First Name
    Andy
  • Gender*
    Male
  • Ford Model
    Fiesta Vignale 140
  • Ford Year
    2018
  • UK/Ireland Location
    Norfolk

Recent Profile Visitors

2,878 profile views
  1. It’s fake news! https://www.reuters.com/article/uk-factcheck-mp-expenses-working-home-idUSKCN21R2IX Sent from my iPad using Tapatalk Pro
  2. Mine does it, nothing to worry about. Sent from my iPhone using Tapatalk Pro
  3. Looks like you’ve answered your own question. Sent from my iPad using Tapatalk Pro
  4. And me. Sent from my iPad using Tapatalk Pro
  5. Sometimes the screen wash additive goes gloopy and sinks to the bottom of the reservoir. The pump has a filter that will stop the gloop from being sucked into the pump. All you need to to is pull the pump out of the rubber grommet in the side of the reservoir (be prepared to get wet when the pump comes out), then give the reservoir a good hosing out with a hosepipe. Had this happen quite a few years ago on a Puma. Sent from my iPad using Tapatalk Pro
  6. I glued mine back together and attached it with black insulation tape. Mine has broken 3 times (The drivers side on was missing when I bought the car, dealer posted a replacement to me). Had 2 Focuses with these on, no trouble at all, the Fiesta is something else though! To be honest I’ve paid for 2; not bothered with a warranty claim, despite the fact it’s a Ford Direct car with 2 years warranty left, however the last time it broke (two weeks ago) I did my repair and so far it’s still on! Sent from my iPhone using Tapatalk Pro
  7. Forscan is your friend here. Enable it and enjoy voice-controlled climate control. After reading this post earlier, as I’d enabled the climate tab on Sync some time ago, I tried it on my way home and it worked. I will say though that the climate screen for the Fiesta is a bit unusual, as Sync presents the dual climate zone screen, not the single zone. Sent from my iPad using Tapatalk Pro
  8. If you start at the inner edge (number plate end) and gradually ease the cover out, you’ll find it comes out easily. A plastic trim remover helps too! Just remember if you’ve got front parking sensors then there’s one in the cover, so be careful not to stress the wiring that’s attached to it. When you replace it just line up the tongues on the cover with the appropriate hole, and press evenly until it’s back in place. I used Autobeam LED’s in mine, and the difference is amazing! Sent from my iPad using Tapatalk Pro
  9. It’s in the APIM menu; btw [mention=94045]Martijn89[/mention] where did you find the LED signature setting please? Sent from my iPad using Tapatalk Pro
  10. Yes, no problems using mine either.[emoji847] Sent from my iPhone using Tapatalk Pro
  11. It turns the stop/start on or off. Sent from my iPad using Tapatalk Pro
  12. Is your A/C switched on? Sent from my iPad using Tapatalk Pro
  13. The BLIS sensors are behind the rear bumper panels obviously towards the rear of the car. Front cross traffic sensor is under the number plate Sent from my iPhone using Tapatalk Pro
  14. There’s now an option to enable/disable engine sound effect on Sync 3 in the newest update of Forscan. Sent from my iPhone using Tapatalk Pro
  15. If your car already has the front radar sensor, you should only need the distance switch or a steering wheel from an adaptive-equipped car. Presumably then this could be enabled with Forscan. BTW, you mentioned in another post about LED signature lighting, that a setting is in Forscan, to enable it, which module on the car did you find this? Thanks in advance. Sent from my iPhone using Tapatalk Pro