• Announcements

    • Stoney871

      Posting in General Chat thread.   11/11/2017

      it has been noted that too many Members are posting messages in the General Chat area instead of the correct Forums. Any messages posted in the General Chat area that are not General Chat will be deleted without warning and offenders may recieve warning points if repeated instances are seen from that Member. There are plenty of different Club areas that encompass 99% of Ford related posts, please select and use the correct one. If anyone is not sure of which area to post something then feel free to P/M myself or other Senior Staff for guidance. The Moderating Staff are having to spend far too much time chasing this problem instead of maintaining the other areas of the forum.


Budding Enthusiast
  • Content count

  • Joined

  • Last visited

About zangaby

  • Rank
    Settling In Well

Profile Information

  • Gender*
  • Ford Model
    Focus 2
  • Ford Year
  • UK/Ireland Location
  1. Mk2.5 Gear Stick Gaiter Clips

    I'm also looking for this part. Any luck so far ? Unfortunately I couldn't find any PN. The part is relatively cheap pn ebay but there are 2 versions, one for the console with armrest (like the one on the first post) and another one for the one without armrest. Without knowing the PN it's quite hard to order.
  2. Mk2.5 (2010) Retrofit Armrest

    One last thing missing, one 4.2 x 16mm screw + one sheet metal nut. So far could't find them on my local store, hope I will find on another one.
  3. When the engine is off there is no message. I was hoping it will signal me before exiting the car that the key is still in.
  4. Unfortunately it's not doing anything when I open the door.
  5. Anyone tried HEC/Page 3 Key outside warning or Key in reminder? I tried ticking Key in reminder but not sure how to check it it works or not.
  6. Mk2.5 (2010) Retrofit Armrest

    Yup, already read it, and noticed that I still need 2 x 6x20 screws, guess the bracket comes without any screws right?
  7. Mk2.5 (2010) Retrofit Armrest

    Can't thank you enough ! I finally made it, just needed a stronger screwdriver. All I need now is that metal mounting bracket(which I already ordered) and I can fit the central console. Hope it goes smooth from now.
  8. Mk2.5 (2010) Retrofit Armrest

    Oh, so I'm not suppose to push those plastic green/red pins?
  9. Mk2.5 (2010) Retrofit Armrest

    Thanks again ! The pictures look great. I read about the second way, there are 2 pins inside, tried to push one at a time and push the metal case, but so far no luck. Not sure how to fit 2 screwdrivers at the same time.
  10. Mk2.5 (2010) Retrofit Armrest

    Should be fairly easy and it's worth having the original one rather than an aftermarket one, still, now I'm stuck on removing the old cigarette lighter.
  11. Mk2.5 (2010) Retrofit Armrest

    I have this set: http://www.ebay.co.uk/itm/141394895960?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Didn't knew about those connectors, I think I will order few of those as they look more factory like. Big thank you for the tip !
  12. Mk2.5 (2010) Retrofit Armrest

    Got it, thank you Stoney !
  13. Mk2.5 (2010) Retrofit Armrest

    HI Stoney871, Thank you but I already have the parts to make the loom as I was doing some wireing in the trunk for the second light lamp. I was curoius weather there is any existing unsused wires I can connect to. Any chace you have a picture with your loom?
  14. Mk2.5 (2010) Retrofit Armrest

    Hi giwrgos_ath, Great guide ! How did you wired the 2 aditional cigarette lighters ? Are there any unused wires underneath the standard console or do I need to piggyback on the standard one?
  15. Mk 2.5 Stop/tail Led Bulbs

    On the facelift you need red PR21W/BAW15s. I'm also looking for some on e-bay but I'm still not sure that they are strong enought during the day. Now there are a lot of models using 5050 leds (3 cips) so they might be strong enough.