Jump to content
Do Not Sell My Personal Information


Mk6 Haynes Favour?


TomsFocus
 Share

Recommended Posts

Evening all,

Got a few bits to fit to the ST in the morning but I like torqueing things properly and not just using the FT method lol.

Could someone take a pic or scan the suspension tightening torques page from the mk6 Haynes for me tonight/early morning please?  :blush:

I know it says it doesn't cover the ST but I would assume the suspension is all the same with the Zetec S.

Cheers in advance!
Tom

Link to comment
Share on other sites


Send IanTT a message. Hes got access to dealerlevel ETIS. I no longer have access to it :(

www.yorkshiredetailing.co.uk - approved resellers of the Highest quality detailing & Valeting supplies

Link to comment
Share on other sites

You again!! Now what? Lol

What torques you wanting?

  • Like 1
Link to comment
Share on other sites

Lol, wishbone and rear shock ones atm 😂

  • Like 1
Link to comment
Share on other sites


Cheers Ian, sorted :)

Next problem though, hulk has done these up, broke an extension and an adapter, and finally a bolt extractor has justfully rounded one.  No idea how I'm gonna get those out. 😞

 

IMG_20160610_140920086.jpg

  • Like 1
Link to comment
Share on other sites

2 hours ago, TomsFocus said:

Cheers Ian, sorted :)

Next problem though, hulk has done these up, broke an extension and an adapter, and finally a bolt extractor has justfully rounded one.  No idea how I'm gonna get those out. 😞

 

IMG_20160610_140920086.jpg

Probably best sticking to a decent local independent garage, especially for older cars for jobs like these, ready access to the the "hot spanner" etc!

  • Like 1
Link to comment
Share on other sites

It's not even 8 years old yet lol...  I expected stuff like this on the 20 year old 306s, not on this though. :angry:

 

  • Like 1
Link to comment
Share on other sites

what bolt extractors are you using? I know the set I use would bite into that and remove it. 

  • Like 1
Link to comment
Share on other sites

Irwin.  There's nothing wrong with the extractors, it's just so damn tight even the extractor slipped eventually and pulled of chunks of metal with it.

I've just damaged one of the stupid low profile sidewalls on a pothole as well...stopped at the petrol station to refill it to get home and find one of my freshly painted brake calipers has been covered in huge lumps of dirt from somewhere.  I honestly give up today...  :mellow:

  • Like 1
Link to comment
Share on other sites

2 hours ago, TomsFocus said:

Irwin.  There's nothing wrong with the extractors, it's just so damn tight even the extractor slipped eventually and pulled of chunks of metal with it.

I've just damaged one of the stupid low profile sidewalls on a pothole as well...stopped at the petrol station to refill it to get home and find one of my freshly painted brake calipers has been covered in huge lumps of dirt from somewhere.  I honestly give up today...  :mellow:

Your not trying hard enough with them :lol: We did a job last week with a front shock pinch bolt. Heated it up nearly red hot, wouldn't budge and was totally rounded. Extractor on it with 600mm bar, couldn't shift it because it was on the deck n my mate was struggling to hold it still. Stuck the extractor into the impact gun and it come out no probs. 

Hammer on a smaller size extractor. 

  • Like 1
Link to comment
Share on other sites

Probably is user error lol, but how does a 10mm bolt even get that tight in the first place?  I was bending the 3ft breaker bar on it that usually takes 35mm hub nuts off!!

I don't have anything to heat it unfortunately, really should get a blowtorch or something I guess, that's all my mechanic mate suggested...but he didn't offer to do it for me haha.

I don't even have an adapter to fit the bolt extractor on the impact gun. :unsure:

Fancy popping over and doing it for me Stef? :tongue: 

  • Like 2
Link to comment
Share on other sites

I'm surprised you haven't snapped it to be honest. Its not even a 10mm bolt, it's only an M6 probably. 

Think your a bit far away for me mate lol, otherwise you'd be more than welcome 

  • Like 2
Link to comment
Share on other sites

Me too lol...  I must admit, Ford bolts often seem to have ridiculously small heads BUT strong shanks...  I snap all sorts of stuff on the Pugs, everything on this just rounds or bends!  I do find it weird having an 18mm nut on the back of a 14mm head bolt (when I refer to size, it's always the head btw lol). :wacko: 

One of the 13mm bolts on the wishbone rear bush had to come out with the 3ft breaker, I was waiting for it to round or snap but it just bent instead lol.

  • Like 1
Link to comment
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




×
×
  • Create New...

Forums


News


Membership