So I've retro fitted powerfold mirrors to my ST Line along with a replacement switch for the drivers side door. Went into Forscan and change the settings in the PDM, DDM, APIM and IPC sections (not AsButilt). Mirrors work fine but now the windows only move a few inches before  stopping. If I reset the PDM and DDM to factory settings, all is well. I'm also getting error codes in both modules which I can't fathom

===PDM DTC C1B15:15-49===
Code: C1B15 - Sensor Supply Voltage -B-

Additional Fault Symptom:
 - Circuit Short To Battery Or Open

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Passengers Door Control Unit

===END PDM DTC C1B15:15-49===

===PDM DTC B1C15:11-49===
Code: B1C15 - Passenger Up/Down Mirror Motor Feedback

Additional Fault Symptom:
 - Circuit Short To Ground

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Passengers Door Control Unit

===END PDM DTC B1C15:11-49===

===PDM DTC B1D06:15-48===
Code: B1D06 - Left Turn Indicator

Additional Fault Symptom:
 - Circuit Short To Battery Or Open

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Passengers Door Control Unit

===END PDM DTC B1D06:15-48===

===PDM DTC U0140:00-08===
Code: U0140 - Lost Communication With Body Control Module

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Passengers Door Control Unit

===END PDM DTC U0140:00-08===

===PDM DTC U2100:00-0B===
Code: U2100 - Initial Configuration Not Complete

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Passengers Door Control Unit

===END PDM DTC U2100:00-0B===

===PDM DTC B1C16:11-49===
Code: B1C16 - Passenger Left/Right Mirror Motor Feedback

Additional Fault Symptom:
 - Circuit Short To Ground

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Passengers Door Control Unit

===END PDM DTC B1C16:11-49===

===PDM DTC P160C:48-0B===
Code: P160C - Control Module Software Performance

Additional Fault Symptom:
 - Supervision Software Failure

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Passengers Door Control Unit

===END PDM DTC P160C:48-0B===

===DDM DTC C1B15:15-49===
Code: C1B15 - Sensor Supply Voltage -B-

Additional Fault Symptom:
 - Circuit Short To Battery Or Open

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Drivers Door Module

===END DDM DTC C1B15:15-49===

===DDM DTC B1C13:11-49===
Code: B1C13 - Driver Up/Down Mirror Motor Feedback

Additional Fault Symptom:
 - Circuit Short To Ground

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Drivers Door Module

===END DDM DTC B1C13:11-49===

===DDM DTC B1C14:11-49===
Code: B1C14 - Driver Left/Right Mirror Motor Feedback

Additional Fault Symptom:
 - Circuit Short To Ground

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Drivers Door Module

===END DDM DTC B1C14:11-49===

===DDM DTC B1D07:15-48===
Code: B1D07 - Right Turn Indicator

Additional Fault Symptom:
 - Circuit Short To Battery Or Open

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC
 - Test not complete

Module: Drivers Door Module

===END DDM DTC B1D07:15-48===

===DDM DTC U0140:00-08===
Code: U0140 - Lost Communication With Body Control Module

Status: 
 - Previously Set DTC - Not Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Drivers Door Module

===END DDM DTC U0140:00-08===

===DDM DTC U2100:00-0B===
Code: U2100 - Initial Configuration Not Complete

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Drivers Door Module

===END DDM DTC U2100:00-0B===

===DDM DTC P160C:48-0B===
Code: P160C - Control Module Software Performance

Additional Fault Symptom:
 - Supervision Software Failure

Status: 
 - DTC Present at Time of Request
 - Malfunction Indicator Lamp is Off for this DTC

Module: Drivers Door Module

===END DDM DTC P160C:48-0B===

Should I be able to do a straight swap or am I missing something?

Thanks in advance.

Have you replaced the PDM and DDM ?

"initial configuration not complete" - Wrong or no software in PDM & DDM, they need flashing to correct level

2 hours ago, unofix said:

Have you replaced the PDM and DDM ?

Not yet but it was on my list of potential solutions.

50 minutes ago, DaveT70 said:

"initial configuration not complete" - Wrong or no software in PDM & DDM, they need flashing to correct level

Can my current ones be flashed to a newer software or is it best to just replace them?

UPDATE:

So I found an AsBuilt file from a car with the same modules that had powerfold mirrors. I compared the PDM and DDM settings compared to mine and made adjustments. I'm pleased to say the folding mirrors worked as well as the windows! The only thing missing at the moment is the Lincoln open feature which is useful but not important at the moment.

Cheers for all the assistance and subliminal points in the right direction.

1 hour ago, Tupoar said:

The only thing missing at the moment is the Lincoln open feature

Pleased you got it fixed.

Out of interest what is Lincoln open feature ?   It's not a term I've ever heard before.

9 hours ago, unofix said:

Pleased you got it fixed.

Out of interest what is Lincoln open feature ?   It's not a term I've ever heard before.

Lincoln open is a feature when the mirrors only open once the drivers door has been open and closed. Useful when you're in a tight parking space. Something for another day...