Jump to content
Do Not Sell My Personal Information

Outside Temperature sensor gone mad!?


Trcek
 Share

Recommended Posts

Hi all, I’ve just completed an oil and filter change on my 2013 focus 1.6 tdci (titanium). All went as normal but on starting the car the outside temperature sensor has constantly read -40. Ran it for around 6-10 mins to see if it adjusted.

I've tried removing a number of fuses, the block connector to the passenger mirror and lastly the positive battery connection in an effort to reset it. 

none have worked so looking for a tip/advice

many thanks

Matt

Link to comment
Share on other sites


6 hours ago, Trcek said:

Hi all, I’ve just completed an oil and filter change on my 2013 focus 1.6 tdci (titanium). All went as normal but on starting the car the outside temperature sensor has constantly read -40. Ran it for around 6-10 mins to see if it adjusted.

I've tried removing a number of fuses, the block connector to the passenger mirror and lastly the positive battery connection in an effort to reset it. 

none have worked so looking for a tip/advice

many thanks

Matt

Hi Mat, 

Don't worry about it. It happened to me as well. It was again after an oil and filter change. I though that I had unplugged or broken some sensor or cable but after a short run the reading was absolutely fine. Some months after I decided to check my ECU for DTC and then I found out that a DTC have been stored probably back then. 

I'm sure that it will be fine. 

BR

Link to comment
Share on other sites

The outside temp sensor is located in the n/s door mirror so I can't see there is a link with oil and filter change . 

Link to comment
Share on other sites

You've probably knocked the plug out for either the engine temp sensor or the MAF sensor.  Both of these make the outside temp default to -40...  I have no idea why but they do!

Link to comment
Share on other sites

  • 1 year later...

My temperature is playing up the reading is saying 3 degrees it tends to go down again can this be fixed 

Link to comment
Share on other sites


  • 9 months later...
On 08/01/2019 at 1:51 PM, Trcek said:

Hi all, I’ve just completed an oil and filter change on my 2013 focus 1.6 tdci (titanium). All went as normal but on starting the car the outside temperature sensor has constantly read -40. Ran it for around 6-10 mins to see if it adjusted.

I've tried removing a number of fuses, the block connector to the passenger mirror and lastly the positive battery connection in an effort to reset it. 

none have worked so looking for a tip/advice

many thanks

Matt

Hi,

Did you get a solution for this. Mine has just done the same after an oil and filter change

Ferdinand

Link to comment
Share on other sites

Hi, 

Mine has been acting up lately too - it's reading about 6-15°C higher than the actual temperature outside, but very occasionally works correctly. 

 

Any ideas on what the issue might be or how best to fix this issue? 

 

Thanks

Link to comment
Share on other sites

21 hours ago, Ferdinand said:

Hi,

Did you get a solution for this. Mine has just done the same after an oil and filter change

Ferdinand

Had my car serviced new years eve and had the same problem.

I ended up driving for around 20/30 mins and it rectified itself slowly as I drove

Link to comment
Share on other sites

Latest Deals

Ford UK Shop for genuine Ford parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share






×
×
  • Create New...

Forums


News


Membership


  • Insurance
  • Support