First thing does these just pop off as don't want to snap anything.

Also is it easier just to buy a new body end with blank blade and get it cut if they cut it like that in the bottom half of the body.

And any links for the best ones in quality etc.

 

Here are some replacement cases cant quite see which one yours is...

 

Key Cases

4 hours ago, Gazcaz said:

Here are some replacement cases cant quite see which one yours is...
 
Key Cases

Cheers mate.
It's for a 2011 titanium with the 3 buttons in a line.

Just got 2 off Amazon for £9.99 on prime, dont need the inside so fine now just getting it cut.

Cheers.

Sent from my SM-G960F using Tapatalk
 

How do you get the blade case open,the open end side pops up but how do i release the other side,its so i can remove the chip to put into a new one.

Cheers

Help needed on this as the picture below shows,the person who had my car before has glued the cover and as on the picture the chip was glued.

So i have 2 new blank keys coming with no chip as you can see it just broke being carbon as i tried everything to get it out but yellow dried glue everywhere.

I would pick a better word thane cheesed off but on here,a dam easy job turns to a money job.

Argh ***** man,, some ***** people have you tried taking to the car to see if it still recognises it ,or is it proper knackered....

Was it just the blade bent originally before you destroyed the rest of it? . In future the blade is removed by tapping out a small roll pin . If you look closely at fob you will see it. 

Pin out then blade comes out. Putting the blade in a vice to straighten. 

The blade is usually removable [emoji21]

There should be a small drift pin holding it into the fob cap.

 

Sent from my SM-G965F using Tapatalk

 

 

 

Think it's 2mm in diameter pin punch to tap out pin

For future reference for others in similar position with damaged blade

Yes the blade bent but the problem i had is it was glued so when i clipped it off on the one end it cracked the plastic.

I looked at a few videos on youtube and it showed just clip off where key hides away and it pulls apart but this was glued and also the Transponder was,you can just see the glue.

Where is this small pin as it never shows it on youtube its just clip one side and pull it open.

Got 2 blanks from Amazon on the way the whole shell with no board etc but i need help on where and what type of Transponder do i get so i will get key cut and programmed.

Look at my photo and you can see where the pin goes , knock the pin out and blade slides out. You wouldn't have needed to remove any of the rest of fob. 

Look at my photo and you can see where the pin goes , knock the pin out and blade slides out. You wouldn't have needed to remove any of the rest of fob. 

I can see the small pin hole on the key blade itself,strange as all the videos never say this dam things.
Anyway it's done now just finding a Transponder now where to get one.


Sent from my SM-G960F using Tapatalk

I've had to have lots of blades cut and fitted to remote fobs. Our drivers at work have a habit of loosing keys. (  both keys) . Usually left in another vehicle to be found 6 months later. 

8 hours ago, iantt said:

I've had to have lots of blades cut and fitted to remote fobs. Our drivers at work have a habit of loosing keys. (  both keys) . Usually left in another vehicle to be found 6 months later. 

Well the blade would not of come out and i have got a fine pin to try to push it out and won't move so must have bent it or something so in

one way at least it couldn't of been done this way, all videos I have seen anyway shows you removing the whole blade as it slots over a round plastic bit

with the spring on it not 1 shows me the pin.

Where is the best place for a new Transponder chip as I know it's the 80 bit one but is eBay the way to go here.

Sent from my SM-G960F using Tapatalk
 

Got no idea where to get transponder chip. Not something we do. New fobs come with them . 

35 minutes ago, iantt said:

Got no idea where to get transponder chip. Not something we do. New fobs come with them . 

If i had known i would have got one with one in but now i have 2 complete key fobs with blades for £9.99 Amazon prime coming today.

Just need Transponder now and key cut,i have sent a message to 3 on eBay just waiting for a reply..£7.

Just rang up our local locksmith,they will supply transponder and cut key and program for £50 so asked him about the 2 as I'm getting 2 and said £80 so don't think that's to bad.

Sent from my SM-G960F using Tapatalk

That's pretty reasonable tbf.

Sent from my SM-G965F using Tapatalk

That's pretty reasonable tbf.

Sent from my SM-G965F using Tapatalk

I did think that so wait them to come today and off I go get them done.
Thanks all on here for your help on this.

Sent from my SM-G960F using Tapatalk

2 new key fobs arrived off Amazon for £9.99 prime and A1 just clips off with very little force on blade end and battery end.
Proves the one I broke was glued as nothing like these 2.

Sent from my SM-G960F using Tapatalk

Just a quick one,keys been all done and coded and starts car...had 2 done.
I have a spare button half with new battery but how do I programme it to open and lock/double lock and open hatch.

Sent from my SM-G960F using Tapatalk
 

Try here..

 

 

https://www.youtube.com/watch?v=LgnUzOcCERE

Try here..
 
 

Cheers,so it's the same on the 2011,did find my ford book to look at about turning the key or something in the ignition and then you have 10 seconds.
Cheers

Sent from my SM-G960F using Tapatalk

Cheers all for your help on this, all done and sorted now for as little as £94 and that's 2 keys which I did only want one so in total now I have 3 spares.

I recommend a place called...Global Security as they Laser cut 2 keys and had their chips and programmed all for £84 and the keys came from Amazon £9.99 for 2.