wiwi35 Posted May 2, 2013 Share Posted May 2, 2013 Hello to allequipment for information: I have a ford kuga 4x2 2.0TDCi 2008here is my problem:after checking by mistake elmconfig in BCM configurationbox kuga 0:4 x2 drive, and DDSerror message on the dashboard and appearance ESP and ABS warning light on permanentlyNo backup madeI have a suavegarde another kuga a friend the same but the rewriting does not work.0 kuga box is not checked in reading.3 error messages in DTC: C276, E0 --- C2769, U0102 --- E0, E0What do you think?sorry but my english is not perfect Quote Link to comment Share on other sites More sharing options...
Preee Posted May 2, 2013 Share Posted May 2, 2013 Go here Enter your VIN number , see if will let you get your AS_BUILT then load the AS_BUILT and save to your car to restore the car defaults save the AS_BUILT data to Notepad and keep safe if you can get it. http://www.motorcraftservice.com/vdirs/SPubs/default.asp?pageid=spubs_as_call&nomenu=yes If this work's please remember to do Page backups when using ELMconfig. Quote Link to comment Share on other sites More sharing options...
Preee Posted May 2, 2013 Share Posted May 2, 2013 Sorry just looking at this i can't see in ELMconfig where to load AS_BUILT so this idea may not work. Quote Link to comment Share on other sites More sharing options...
Preee Posted May 2, 2013 Share Posted May 2, 2013 You could always have a look at this program see if you can use this to load the as_built. FDS.zip Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 software installation and after reading it gives these impressions screens below.Sorry I hid some data because I do not know if this is exploitable by dishonest persons outside the site. I think you understand me.What to do now to read this??I did not backup??can you give me the procedure to save before eventual change that seems fair.thank you for your interest in my mechanical problem Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 I managed to have my as built VIN request with my motorcraftservice.com.I save in text formatWhat should I do now? Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 I put my original built, I found that everything is delivered as the original except that both lights are still there. On the software elmconfig DDS is always checked and ford, he is not??? weirdstill same error elmconfig and impossible to erase. Quote Link to comment Share on other sites More sharing options...
Preee Posted May 3, 2013 Share Posted May 3, 2013 Ok With FDS try and un-tick DDS then save to car , disconnect and the re-connect see if that clears it , you could also try the Restart module function to see if that clears the fault. Quote Link to comment Share on other sites More sharing options...
Preee Posted May 3, 2013 Share Posted May 3, 2013 You could also try the English version of ELM-FF2 on the first page of my guide see if that helps. Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 impossible to click on load or save left, is this normal? Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 DDS isn t check on FDS but only on elmconfig Quote Link to comment Share on other sites More sharing options...
Preee Posted May 3, 2013 Share Posted May 3, 2013 DDS isn t check on FDS but only on elmconfig Then try and check it and save , then dissconnect then go back and see if you can then un-check it , it might just be a glitch where is stuck , three programs you could try all three to remove click/un-click maybe one might remove the error. Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 3, 2013 Author Share Posted May 3, 2013 ok I'll try to recheck and record and see if it unlocks the module on elmconfig on FDS i don't know Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 4, 2013 Author Share Posted May 4, 2013 no communication with IPC module is faulty. Even a colleague with a suitcase can not correct that the kuga is 4 * 4 * 4 instead of 2.I was looking for a solution contnue Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 6, 2013 Author Share Posted May 6, 2013 with FF2 and elmconfig I do not manage to reset the IPC module do you know the solfware FOCOM Apparently it would be the most appropriate???? Quote Link to comment Share on other sites More sharing options...
Preee Posted May 6, 2013 Share Posted May 6, 2013 I have never used that software no. Try Loading FDS , and click to get your As_built see if that works , or try and load your as_built before you connect to the car then if it loads try and send to the car that way. Another thing that may be worth a try is with your mates Kuga Download and save his as_built file from his Kuga , edit it to exactly what yours should be and try and upload it to your car, Quote Link to comment Share on other sites More sharing options...
Preee Posted May 6, 2013 Share Posted May 6, 2013 Just a thought did you also under HEC un-tick AWD Kuga Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 7, 2013 Author Share Posted May 7, 2013 HEC in the AWD box is not check. Should I check knowing that I have a 2x4 and not 4x4? Putting the as built of my friends wrong t it injects its VIN??? Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted May 7, 2013 Author Share Posted May 7, 2013 I try this solution this afternoon. Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted June 7, 2013 Author Share Posted June 7, 2013 No software happens to erase errors. So this week stint at Ford because the module does not respond, so he stays on despite the different software used Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted June 19, 2013 Author Share Posted June 19, 2013 I am has the search a person possessing the IDS software to have access to HEC so possible coach not possible with FDS of loader Quote Link to comment Share on other sites More sharing options...
wiwi35 Posted July 10, 2013 Author Share Posted July 10, 2013 Direction(Management) 02 garages ford yesterday then suitcase with the software IDS but the impossible to integrate(join) and to collect the information of origin!!! Strange but I think that they did not know well enough the possibilities of the software. They were very cool when même. - I try to find a person knowing perfectly the software and using him(it) regularly. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Ford UK Shop
Sponsored Ad
Name: eBay
Ford Model: FordUK Shop
Ford Year: 2024
Latest Deals
Ford UK Shop for genuine Ford parts & accessoriesDisclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.