mikeyjbartlett Posted March 3, 2017 Share Posted March 3, 2017 Hi there guys, I'm new to this forum so please bare with me. I've retrofitted the Sony Navigation unit to my 2014 Fiesta TitaniumX, all is functioning after buying a FAKRA GPS Antenna and it does route and talk to the cars CANBUS network absolutely fine, so I can change car settings like traction control and Ambient lighting. I programmed the navigation unit in FORScan by enabling the Navigation Module under the IPC. I also changed the display version to MFD5 instead of MFD4 and that meant my speedo went back to Miles on the odometer instead of KM, and I can change it in the settings now. My only concern is I don't get ANY voice. The radio turns itself down and nothing comes out. I don't know if there is supposed to be a speaker in the top grille above the display unit, but I haven't got one. Is this a software problem? Thanks for all your help. Quote Link to comment Share on other sites More sharing options...
JW1982 Posted March 3, 2017 Share Posted March 3, 2017 This problem is most likely caused by 2 missing (audio) wires between the display and the audio unit. On a car without Satnav these 2 wires are usually missing. This problem can easily be solved by inserting the missing wires. the easiest way to obtain these wires is by cutting them out of a scrap car at a local scrap yard. Quote Link to comment Share on other sites More sharing options...
mikeyjbartlett Posted March 3, 2017 Author Share Posted March 3, 2017 Where do the wires go in to? kind regards Quote Link to comment Share on other sites More sharing options...
Ben.s Posted July 5, 2017 Share Posted July 5, 2017 Hi I have the same problem with my car installed navigation and connected everything up no audio from nav through Speakers I have got wires coming out of fcmd in pin 12 and 6 into the loom some where it nothing in pin 4 and 5 on stereo I tried to connect a wires between the pins as stated above and have no audio coming through at all any ideas I have st2 2014 it's beginning to puzzle me now Quote Link to comment Share on other sites More sharing options...
Ben.s Posted July 5, 2017 Share Posted July 5, 2017 Hi again when you say connect 2 wires do you remove the 2 wires out of the back of display and just connect them to the stereo pins or do you have to run a lead on its own between the display and stereo. Pins with the existing wires that are i the back of fcdim Quote Link to comment Share on other sites More sharing options...
Aego Posted September 16, 2020 Share Posted September 16, 2020 On 3/3/2017 at 7:45 PM, JW1982 said: This problem is most likely caused by 2 missing (audio) wires between the display and the audio unit. On a car without Satnav these 2 wires are usually missing. This problem can easily be solved by inserting the missing wires. the easiest way to obtain these wires is by cutting them out of a scrap car at a local scrap yard. I just fitted the Sony display, audio unit and front button panel from a 2012 Focus Titanium X (sat nav) into my 2012 Focus Titanium (Sony non sat nav) with a fakra gps off amazon. All working, 5 satellites but no sound/verbal commands through Speakers whilst using satnav. Am I supposed to do something in Forscan? I have it and an elm. What/where are the two wires?? Thanks for any help please Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Ford UK Shop
Sponsored Ad
Name: eBay
Ford Model: FordUK Shop
Ford Year: 2024
Latest Deals
Ford UK Shop for genuine Ford parts & accessoriesDisclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.