PaulB1803 Posted April 9, 2012 Share Posted April 9, 2012 Finally got chance to modify the reader today. Activated autolocking and auto heated screens. Locking works fine but will have to wait for a cold morning for the screens. Thanks again preee . :) Quote Link to comment Share on other sites More sharing options...
Preee Posted April 9, 2012 Author Share Posted April 9, 2012 Finally got chance to modify the reader today. Activated autolocking and auto heated screens. Locking works fine but will have to wait for a cold morning for the screens. Thanks again preee . :) great news Paul. I have found out a couple of things , EHPAS only works if you have 1.8 or higher engine. Shift gear Light only works if your ROM file is above 508 , you can access that info from the Dash test mode. Quote Link to comment Share on other sites More sharing options...
MrGrumpy Posted April 9, 2012 Share Posted April 9, 2012 I still cant download the files properly, could my software to unzip the files is corrupt or something.. Ive tried different software and its driving me nuts :( Ive still got to order the device so when that arrives ill have another go Quote Link to comment Share on other sites More sharing options...
Preee Posted April 9, 2012 Author Share Posted April 9, 2012 What happens when you try and download the files? are you sure a bar at the top of the screen does not come up with the option to download , or are you talking about not being able to un-zip the files? Quote Link to comment Share on other sites More sharing options...
Pidu Posted April 10, 2012 Share Posted April 10, 2012 I still cant download the files properly, could my software to unzip the files is corrupt or something.. Ive tried different software and its driving me nuts :( Ive still got to order the device so when that arrives ill have another go In case of need pm me your email address and I will send you the software you need. Quote Link to comment Share on other sites More sharing options...
jay1981 Posted April 10, 2012 Share Posted April 10, 2012 A quick tip for Windows 7 users. Windows 7 user account control does not let you install the dllpack.zip files into the windows\system32 folder. What i did was copy the files manually using drag and drop into the system32 folder, then right click on the RegDll.bat file then click Run as administrator. No problems then B) Quote Link to comment Share on other sites More sharing options...
Richiemac Posted April 13, 2012 Share Posted April 13, 2012 Messing about with this earlier and found if you check the boxes in the attached image, you can access all menu options on the move..........previously while driving i could only disable ESP , all other functions were blocked.........not now Quote Link to comment Share on other sites More sharing options...
MrGrumpy Posted April 16, 2012 Share Posted April 16, 2012 A quick tip for Windows 7 users. Windows 7 user account control does not let you install the dllpack.zip files into the windows\system32 folder. What i did was copy the files manually using drag and drop into the system32 folder, then right click on the RegDll.bat file then click Run as administrator. No problems then B) Thats great i have been ripping my hair out trying to get this done properly, but this has worked. Thanks Quote Link to comment Share on other sites More sharing options...
Lenny Posted April 16, 2012 Share Posted April 16, 2012 Thats great i have been ripping my hair out trying to get this done properly, but this has worked. Thanks Mr.Grumpy seems to be not so grumpy any more ;) 1 Quote Link to comment Share on other sites More sharing options...
rokos Posted April 18, 2012 Share Posted April 18, 2012 Hi everybody. Any further developement for this software? I wonder if may coding injectors is possible? Quote Link to comment Share on other sites More sharing options...
Preee Posted April 18, 2012 Author Share Posted April 18, 2012 Hi everybody. Any further developement for this software? I wonder if may coding injectors is possible? I'm following the build Topic from civil-zz , he has made a couple of tweaks to the program recently but is still working on it , not major changes as of yet , there is nothing in there as of yet regarding coding injector's. Quote Link to comment Share on other sites More sharing options...
Sliveredge Posted April 18, 2012 Share Posted April 18, 2012 Great program and guide guy, I have enabled a few things on my Speedo but the main one I would like to activate is there DDS do I need to mod my ELM to access the BCM tab in the ELMconfig software? Cheers great site BBW Quote Link to comment Share on other sites More sharing options...
Preee Posted April 18, 2012 Author Share Posted April 18, 2012 Great program and guide guy, I have enabled a few things on my Speedo but the main one I would like to activate is there DDS do I need to mod my ELM to access the BCM tab in the ELMconfig software? Cheers great site BBW Yes you will need to modify your ELM 327 it's very simple to do . Quote Link to comment Share on other sites More sharing options...
rokos Posted April 18, 2012 Share Posted April 18, 2012 Great job both of you. Keep going... BRAVO Quote Link to comment Share on other sites More sharing options...
Lenny Posted April 20, 2012 Share Posted April 20, 2012 Great program and guide guy, I have enabled a few things on my Speedo but the main one I would like to activate is there DDS do I need to mod my ELM to access the BCM tab in the ELMconfig software? If like me, you dont have any soldering tools to re-configure the ELM 327, i printed out pree's guide and brought it along with the purchased switch and the ELM327 to my local computer&Console repair store and asked them to do it for me, they charged me 20euro and three days later collected the finished item and i had it connected to my car and running the software. Quote Link to comment Share on other sites More sharing options...
fffog Posted April 20, 2012 Share Posted April 20, 2012 Is it possible to R/W flash memory? I can't wait to use this greate tool instead of VCM. :D :D :D :D :D Quote Link to comment Share on other sites More sharing options...
Preee Posted April 20, 2012 Author Share Posted April 20, 2012 Standard Flash Memory is re-writable , what is it your thinking of doing? Quote Link to comment Share on other sites More sharing options...
Teabags Posted April 22, 2012 Share Posted April 22, 2012 I've downloaded the new English translated software however in the auto lock feature there are two further options which one do you select? Thanks Quote Link to comment Share on other sites More sharing options...
Preee Posted April 22, 2012 Author Share Posted April 22, 2012 I've downloaded the new English translated software however in the auto lock feature there are two further options which one do you select? Thanks You select Auto locking enabling by customer Quote Link to comment Share on other sites More sharing options...
Teabags Posted April 22, 2012 Share Posted April 22, 2012 You select Auto locking enabling by customer Thanks Quote Link to comment Share on other sites More sharing options...
Teabags Posted April 22, 2012 Share Posted April 22, 2012 Just another quick question because I've had the ford approved mountune performance upgrade will it still be possible to access the cars ecu? Quote Link to comment Share on other sites More sharing options...
irl-06lx Posted April 22, 2012 Share Posted April 22, 2012 is there anything specific i need to do to get this to work with a win7 laptop? Quote Link to comment Share on other sites More sharing options...
Richiemac Posted April 23, 2012 Share Posted April 23, 2012 Works fine on W7 , both 64 and 32 bit.........did you run the DLL pack first ? Turn off user account control and install them......... Go in to 'devices and printers'......find the lead and set the COM port to 1 in advanced properties........ Will work ok :) Quote Link to comment Share on other sites More sharing options...
irl-06lx Posted April 23, 2012 Share Posted April 23, 2012 ive tried installing the dll pack, turned of user account control and ran as administrator but when i open the english software it gives that same error mscomm32 is missing etc... no idea whats going on! I copied the 4 dlls to system32 and ran Reddll as an admin... is this right? got it, copied straight to windows folder not system32. however now to rattle your brains, every time i click read i get this error. some pages fill in the fields with "n/a" and some give this box. any ideas? Quote Link to comment Share on other sites More sharing options...
Haz93 Posted April 23, 2012 Share Posted April 23, 2012 @irl-06lx This is where the cable modification is needed. Anything on the right hand side (HS-CAN) can be edited as standard, to edit the left hand side (MS-CAN) you must add the switch so you can change the CAN mode of the reader. this is described by Preee on the first page @Teabags You can't edit the ECU at all with the current software, only the options shown in the picture above posted by irl-06lx, such as the GEM (general electronic module), the HEC (Hybrid electronic cluster(onscreen display)) etc.. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Ford UK Shop
Sponsored Ad
Name: eBay
Ford Model: FordUK Shop
Ford Year: 2024
Latest Deals
Ford UK Shop for genuine Ford parts & accessoriesDisclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via the club
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.